This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
My question may seem silly, I did not so long ago been programming NRF51822 S130. I use examples experimental_ble_app_blinki. I want to get the module ID smartphone when connected...
If I set the I2S peripheral on the nRF52 to mono, ie CHANNELS is either LEFT or RIGHT, what does it actually output? I'm sure it still toggles the LRCLK line to indicate left...
I'm working on a battery - operated device where the battery is soldered onto the device, which makes it inconvenient to pull power to the device. I might be able to get to...
Hello,
I have some problem in DFU.
I ask this again.
I did as below.
Key generation
nrfutil keys generate c:\vault\priv.pem
public key generation in...
Dear Nordic Team,
I can't launch Sniffer on PCA10000 using MCP nor on PCA10040 using nrfConnect. In case of MCP I get "No response from master emulator" and in nrfConnect...
Hi,
is someone of you aware of a portable (Win, Linux, OS/X) GATT client library, prefereable with C++ binding? The only one, that I've found so far is Qt. What do you use...
I have been using nRF8001 equipped Arduinos for a few years now with great success. I exclusively use apple software on the other end. I have a new application that will required...
i want use a 9 axis IMU sensor (3 axis accelerometer,3 axis gyroscope and 3 axis magnetometer) in nrf51822 is it possible and how the transmission of values takes place.....
Hi,
I'm using the bootloader in nRF5_SDK V12.0 with nRF52832. I have some problems want to know:
How to make it run application first after I program softdevice...
I notice that the track which runs from P0.11 (E4) is connected to GND at pads C3 and C4. Is this intentional? If P0.11 is required for GPIO usage, is it necessary to go to...
I am trying to update my project to SDK 12.2 which was released this week and I am getting a ton of compiler errors with the FreeRTOS source files. For example, I try an compile...
I'm a begineer in nRF52DK and S132.
I am trying to make an application code to enable link layer control procedures at any time in a connection state with the nRF52DK and...
hello everyone，
Which APP demon is the most stable APP？
I use nrf-master APP to test the blue device，it can connect very well。but when I use uart-app ， it can't connect...
