Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
hello,
I've encountered a problem with our own nrf51822 circuit not advertising.
Our circuit is exactly the same as what is given as the reference circuitry on the datasheet...
It's the first time i'm using the spi to connect various slaves, so is there any example how to communicate a raspberry with 2 or more nRF24L01 on the same bus?
Thanks in...
Today I have recieved the new nRF52 Development kit PCA10040. I did a update for the nRFgo Studio to version 1.21.2.3.
The softdevice s132_nrf52_2.0.0 will be flashed without...
OS: Windows 10
Target: nRF51-DK
Tried to connect with nrf51-dk with Keil MDK-Lite v5.18a.
The default Jlink version used along with this IDE was v4.98e
the 'download...
Hello all,
I'm looking at the example projects and ble_app_template in particular, and have noticed something that doesn't seem to make sense...
In main(), this project...
Hi, I am looking for a Bluetooth Low Energy Soc based solution like nRF51822, but I'd like to have an open source firmware solution...
Do you have that kind of solution...
Hi
I want to execute my app from the RAM to test if i'll get a considerable decrease in the current consumption.
I'm using : "s130_nrf51822_0.9.0-1.alpha" &"nrf51822QFAC...
Hi
I'm trying to change TX power and measure the current consumption while advertising, (DC/DC disabled) and i get an increase of 3.44mA from 0dbm to 4 dbm. Ok That's logic...
I follow the instruction and I am able to connect to Xively MQTT service. But I am confusing how to connect to AWS IoT MQTT.
AWS claim it support IPV6 as well.
Is there...
Hi all:
Here is my develop environment and it always show the message "one or more breakpoints could not be set and have been disabled".
Is any item I missed.
OS:Ｗｉｎ１０...
The ble_app_gls example does not provide any handling code for BLE_GAP_EVT_TIMEOUT, BLE_GATTS_EVT_WRITE, nor BLE_GATTS_EVT_HVC. I'm trying to understand whether the lack of...
I just ran a few experiments on calling sd_ble_gatts_hvx() multiple times based on SDK v10's ble_app_uart example. I have configure the app so that it for each external event...
