Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hey everyone, I'm trying to compile blinky example, using ARM on Mac OS X. I use st-link 2 to flash it. So, the first when I do 'make' command I've got errors
Makefile...
Gentlemen,
I apologize if this is not the correct place to post this question.
I have a potential project to start a BLE project but their requirement would be start...
I'm developing a new board with nRF8001, after reset i correctly get the DeviceStartedEvent 0x03 0x081 0x02 0x00, after that i go into setup mode sending the configuration...
Hi,
I am using nRF5_SDK_11.0.0_89a8197 at center to debug ble_app_uart_c project.
The center can connect the device well at the beginning. But if I power on and power off...
according to the introduction of mesh framework( value storage part), it says all mesh data is saved in a structure. My understanding is : Handle means a trickle instance...
How to configure S130 Softdevice as Completely Central(S120) i.e with Out Switching its mode to peripheral to operate like a central.
Is there any API or Example to do...
For example, if the first page is erased then it will set this page as swap page and continue looping without increasing the 'page' variable.
This means that the last...
Hi,
I have flashed boot loader to 0x7A000 (Size 24kb) and Softdevice to NRF52 DK ,then flashed application using nRF connect .
Am also able to update application after adding...
Hi,
I need PWM on 2 pins, with a varying duty cycle, and read some posts in this forum on the subject.
I am still using SDK7.2.0, with SD7. Our product is stable, so I...
Hello, a few days ago I was having trouble with RF performance on a custom PCB using the NRF51822. I posted here to get feedback and figure out where the design went wrong...
sdk : v8.1.0
os : ios
tool : nrf tool uart
use the ble_app_uart, it worked normaly. and add duf fuction in the application by the notice
[http://developer.nordicsemi...
Dear all
I found that the frontline BPA sniffer can't catch the connection data between Android5.1 or ISO and BLE device. Does this normal? How can I use the sniffer to...
Hello, I have to implement infrared sending and receiving of a modulated signal in pre-existing code.
I have managed to implement infrared sending thanks to the ble_app_uart_IR...
Hi!
I have creat two timer with app_timer_init.
start the first timer trigger every 4 ms, every 125 times(approximately 0.5 sec) to start the second timer which trigger...
I am having issues using the correct definition for the clock config:
for
nrf_clock_lf_cfg_t clock_lf_cfg = NRF_CLOCK_LFCLKSRC; SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL...
