I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi, I would just like to know if there's an equivalent to "BLE_GAP_EVT_CONNECTED" for services discovered. There's some stored data I want to send in a loop only after services...
Hi,
Does the nRF51822 have a capability of responding to multiple phones?
I am working with RFduino using the RFD22301. I'm assuming that the RFD22301 is the same BLE...
Hey,
the nRFgo Studio contains a simulator for the nRF8001 and 8002. Will there be an update in the near future to simulate the bahaviour of the nRF51 platform?
Mar...
I have TIMER2 running at 500us interval. ANT is working as 100Hz master.
Understood softdevice will affect the timing and cause some latency.
I am guessing it is delaying...
Hi:
I'm implementing an controller for an open source drone Crazyflie ( www.bitcraze.se/.../) . My device is similar to pca10001 board.
Since Crazyflie is acting as peripheral...
Hi all!
I've been unsuccessfully trying to DFU the Smart Beacon Kit with the latest firmware.
Using the nRF51 DK and the TC2030 tag connect cable I was able to program...
I am trying to get a communication between two pieces nRF51822 using the my service. I checked the peripheral with Master Controll Panel app and is working fine. The multilink...
Hi,
I have the (IoT) environment running. The Raspberry Pi (with Miredo tunnel) is connected to the outside world. I can ping6 the ipv6.google.com server from Rasperry...
Hi Team,
I am using nrf-51 DK as sniffer.
I need some guidance regarding how to study or analyze these packets?
I don't know what exactly I should check in each REQ...
Hello,
I am working on nrf51822, My requirement is to upgrade the firmware over the uart with help of DFU.
I have made code for that on controller side and fortunately...
In the release notes of the nRF51 SDK v8.0.0, section "Supported devices" it says that "This SDK is optimized for IC revision 3".
I am using a Laird BL600-SA-04 module...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Howdy, I'm trying to DFU my 51822 beacon v1.1.0 with MCP. MCP is failing the transfer. Steps I have taken are:
-Programmed my beacon with segger from the dk, both the SD...
There are apparently only 3 S120 examples available, and one of them is a peripheral example, which can be done with the S110, so really there are only two examples. This...
