My firmware is using SDK 17.0.2, and it includes CPS, battery, and a custom service. Everything has been working fine. The custom service is responsible for sending and receiving...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi,
The following URL does not include nRF54L15, is it supported?
https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/samples/openthread/coap_server/README.html
...
Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hi,
while flashing the device i get "Contents mismatch at: 0001C1C0H".
I am not sure if my IROM1 and IRAM1 settings are setup correct in the Target Settings of my Keil project...
Hi,
i have two microcontrollers: STM32F401 and nRF51822. They communicate by uart with flow control. I use 110 Soft Device from SDK 10. The maximum baud rate when communication...
Hi All,
I am trying to update the HEX file of LED_mesh example using DFU bootloader over-the-air. The LED_mesh application HEX file gets uploaded successfully by bootloader...
Hi Nordics,
I copy pwm sample code into my proximity project, to drive a buzzer .
I init pwm before softdevice. but, once "SOFTDEVICE_HANDLER_INIT" is excuted, the buzzer...
Hi,
i have a problem with nRF51 an nRF24LU1+. I use S110 and micro-esb library. I can switch beatween poroperty RF and bluetooh ( never run both in the same time ). When...
I wanted to use the SysTick timer for timing in my application, but even when writing a handler and trying to set it up, it doesn't seem like the interrupt is ever triggered...
hi I am i using Keil to debug the progam, it seems like that the printf() function can't work in keil, so i use jlink RTT to perform the printf function to collect data ....
HI,
i want to have a application in which a timer timeout say 5 second. and during this timeout there is another timer say 1 second. whenever the 1sec timer timeouts then...
Hi,
The function sd_ble_enable(ble_enable_params_t * p_ble_enable_params, uint32_t * p_app_ram_base) requires now the application RAM base address! Is it 0x20002800?
Hi ~
I use nrf51-micro-esb on GitHub
In Tx-Device: auto sent (data+1) to Rx-Device
But Rx-Device receiver data still the same not Increment....
why in Rx-Device...
Hi everybody
Since quite a long time since my last visit here. Now I come back because a new project using the NRF51822. Because now I'm using the NRF51822-CEAA, I can...
Hello,
I am developing an application where in i want to create a network with One central[not a mobile,pc,tablet etc] and multiple peripherals connected to the central excahnging...
HI,ALL
my Project can not exit the GPIO INTERRUPT HANDLER.
following is my project.
include "nrf_gpio.h"
include "nrf52.h"
include "boards.h"
define BUTTON_1...
I have found the bellowing code which was in s130/ble_gatts_struct_seriallization.c of nRF51_SDK_10.0.0 : ( ble_gatts_attr_md_enc)
/* serializer does not support attributes...
