در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
I have two nRF24L01+, one as PTX and one as PRX.
Both have following config: EN_RXADDR = ERX_P0, EN_AA = ENAA_P0, RF_CH = 100, RF_SETUP = 0x26, SETUP_RETR = 0xF0, SETUP_AW...
Hello, i have bought nRF51822 pcb module on Aliexpress (nRF51822 CEAA chip HWID 006A, 16Mhz crystal) and I'm trying to test it with SDK 6.1.0 and S110 v. 7.3.0 (as compatibility...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
Hello,
Using BLE Scanner app (available for Android), i'm able to change the device name. I can also write other values for each characteristic.
How can we protect a...
Hi,
I use nrf51822 with SDK8.1, S110 and gcc with Makefile. I want to use nrf_drv_twi in both my main “.c” file as well as a library “.c” file that is included in the build...
This is SDK 8.1.0, Softdevice 7.3.0 (not being used for this demo), running on a NRF51822-CEAA.
The minimal program below just sets the WDT for 10 seconds, then goes into...
Hi,
I have designed a custom board with nRF51822 but when I connect the custom board and j-link with an adapter the program nRFgo can't detect the chip.
When I conenct...
I'm using DK as the programmer connected (via Debug Out) to a naked nrf51 module (Rigado BMD-200). I can program it via DK, but RTT doesn't work (no output in J-Link RTT Viewer...
With the new nrf_drv_gpiote, how can I know if the handler has been trigged by event "low to high" or "high to low"?
Please, could you provide a configuration exemple?...
Hello,
I am a beginner. Just bougth a nRF51 DK but have not received it yet.
My second question of the day, very related to my first one, but thoutgh they were different...
Hello, beginner here. :)
I just bought an nRF51 DK, but have not received it yet.
I decided to test it because my older BLE module (HM-11) only allowed me to scan beacons...
Hello.
I installed all of relevant software tools and compiled blinky_example with nRF51822 Dev B/D.
Unluckily, build result is like below.
._build\blinky_arm.axf:...
I have built an application using SD120 v2.1.0. The app runs fines from 0x1d000. When I run an own bootloader (RS485, no need of interrupts or SD120, no pstorage functions...
Hello, My question is that in sleep mode my nrf51822 current consumption is 0.98mA, with only GPIOTE enable, however when I disable it, the current falls to 13uA, but the...
