Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi guys I'm sending data from an nexys 4 fpga through an spi to my nRF51 (pca10028) I have the fpga set as the master and I'm able to read data sent to the nRF51 through my...
Hi.
I'm using nrf52 as slave for another device. I'm reading test string from the nrf buffer and I can see extra zero (rest of the content is then offset by one -> corruption...
Hi, i know this question has been ask before but, i was reading and readind and i could find a way to do it. I got the theory but when i'm going to implement it in my code...
Hi there,
i cannot get the hrs_c example to connect to a heartbelt.
The heart belt is found and a connection is established:
[APPL]: >> DM_EVT_DISCONNECTION
[APPL...
Hi
I am working on nrf52 using BMD300 RIGADO board.I am trying to run BLE UART example of nrf SDK 11.0.0.But while I am running the code I am getting errors as
: struct...
In Nordic infocenter/nRF5 SDK v11.0.0/Examples/Bluetooth low energy examples/BLE Central & Peripheral/, I found a example project which name is "Experimental: BLE LE Secure...
BLE is first initialised in my code, then SPI is initialised. If no SPI transfers are to be executed in the code, the code compiles, runs correctly and BLE functions correctly...
I have a very simple program that generates a 50% duty cycle clock using the NRF_PWM0 on the new nRF52 device. Unfortunately, my Tektronix 1GHz oscilloscope doesn't lock to...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
Is there a way for firmware running on the nRF52 to detect the presence of a SEGGER (or other) SWD capable device? I've looked through all the nRF registers but couldn't find...
Hi all
Our application, built on the NRF51822 Rev. 3 and the SoftDevice S130 V1.0.0, uses the UART0 with 115'200 baud, 8N1, to communicate with another controller/PC. Hardware...
Hi, In my project I want to read data from i2c and update in advertising data and the board need to advertise without time out (i.e 24x7) for these I take advertising timeout...
Hi,
I am new to the BLE profiles. I am have to send the TMP007 temperature sensor values to mobile APP using BLE HTS profile. for this I am using sample example of nrf52...
