Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I need to use the 8.0.0 version of S110 with my beacon which contains 7.1.
Since the Android DFU utility supports updating the Bootloader and softdevice with a zip distribution...
hi,guys
For testing the comunication between BLE+timeslot device and radio device, I change the code as below:
void start_timer(void)
{
NRF_TIMER0->TASKS_STOP = 1;...
Dear Nordic,
Whats wrong with the below code. It works well in RFduino but when I try to port the same code in Keil environment.Its not working throwing error as
1.identifier...
I just got a new target board back from fab/assembly and I'm trying to use the debug out connector on the PCA10028 to program the new target.
My target is the NRF51822...
Is there a beginners guide on how to get a console output working for the following setup?
keil v5 & SDK 6.1
nrf51-dk connected with the
TC2030-MCP-NL to a
nrf51822...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hello,
I am new to working with nrf52 and was looking for a way to make printf work in a blank project that I have created. I followed the uart example for the peripheral...
Hi
Now I'm using the pstorage module to save some data.But I meet some problem,I hope I can get your help,thanks a lot.
It seems that the block has been created successfully...
Hello everyone
i am trying to run the pwm library exmaple from github into the SDK VERSION 9.0 but it is showing lot of errors like
............\components\drivers_nrf...
Hello,
I am working on S110 SDK 9.0 and softdevice 8.0 on EK board. I am able to authenticate the connection using static passkey.
I need the information about encrypting...
A LOT of great information is presented by the engineers. Is it possible to post videos of the presentations?
Apple does this for the WWDC sessions. I find myself watching...
Hello Everyone,
i ahve been working on NRF51 series for past two months but suddenly i came to know about NRF52 series the apckage is ame and proce also not varying much...
Hello,
Now I am using nrf51822 with PCA10004 EK board. And the custom board we are using is BL600-SA module. As BL600 can be used with nrf SDK and softdevice, Can I use...
I have a Bluetooth LE dongle and I have also a BLE device that I want to communicate with.
On the BLE device there are a several services like Cycle Power (0x1818) and Device...