Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hey Guys,
In my custom board I need to use two different I2C bus and one SPI.
At the moment i'm using twi_master to comunicate with one of the TWI bus,
but to switch...
I have several nRF6930 beacon kits. Some have a sticker indicating they have a PCA10006 board, on others, the sticker indicates PCA20006. All PCBs are marked 400059 0138RUBR...
Dear developers,
As we know, nrf51 has a maximum flash erase / write cycles of 20.000 times. So, in my code, I have implemented a counter that checks if max. flash write...
Dear All,
Does it worth coding a selection (scanning?) of "relatively free" radio channel to stick to?
Say, before starting our distributed application (consider a network...
Hi,
The artical form this link is great !
devzone.nordicsemi.com/.../
but I've some interogations.
the clear text contains the nonce value; 12 random bytes starting...
Dear Nordic,
I have managed to modify the HID Keyboard demo (SDK10/nRF51 DK) to have both keyboard and consumer control functions. Works fine on Android, however it shows...
How should the addressing be between an nrf24LU1+(transmitter) and nrf24l01+(Reciever) in the code.?
The registers TX_ADDR, RX_ADDR_P0, RX_ADDR_P1 are updated on a device...
Do we need to explicitly set the ENABLE field (Bit31) of RADIO->OVERRIDE4 when applying the override values from FICR->BLE_1MBIT[n]?
From the few samples I've checked,...
Please teach me the minimum theoretical value of the transmission time in the following conditions.
CPU --> nRF24L01 --(2.4GHz/1Mbps)--> nRF24L01 --> CPU
CPU -->...
I need to send a long (let's say 10Kb) notification from Bluez 5.37 on my Linux device to a mobile phone.
My implementation is based on src/shared/gatt-server.c .
I...
Hi,
I have put in my chip (nrf51422):
-1 softDevice s110 8.0.0;
-2 application (hrm_whit_dfu);
My problem is:
when i send characteristic to start advertising the board...
Hi everyone,
I am new to nRf series and have just started to use the nRF51 Development kit(nRF51422). I am using the s130 softdevice and I have seen that the sofdevice supports...
I'm trying to test out pin change interrupts using the PCA10028 dev board. I'm using two buttons to turn off and on an LED. The code below is only generating events from button1...
I have a custom board designed which implements a Arduino Micro (ATmega32U4) and an nRF8001 chip based upon Richard Clarks' nRF8001 breakout . The Arduino FW uses a slightly...
