I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I usually use electronics.stackexchange.com/.../15143 approach for decoupling capacitors and until now I had much better EMI performances.
I make sure that tracks...
We would like to reduce the attribute table size a little to increase free RAM. Are there any guidelines explaining how we can judge how large the table needs to be for a...
I compile SDK7.2 example hrs in "experimental_s110_with_dfu" by eclipse,
and I download softdevice & bootloader by nRFgo
then i use master control panel to DFU the hex which...
In the nordic documentation it mentioned that in the init packet we can write list of supported softdevices so that if one of that matches it will start the dfu. But in Signed...
Actually, I'm not good at using English. So I'll try to struggle to type this question...
Sorry, Last week. My boss gave me a Nordic Mouse to develop some embedded one...
Hello,
I am using nRF51822 and meet a question that in the process of bluetooth communication, I will get an instruction for external circuit to stop bluetooth function...
While both P0.00 and P0.01 has Analog Input function, initializing an AnalogIn (in mbed) with P0.00 will cause the firmware to fail to start at all; but initializing using...
Please tell me the Manufacture Part no: which is used for the 16MHz crystal in the PCA10040 DK. I found it different from the one used in PCA10028 version of the DK with just...
Please tell me the location to download the hardware files for pca10040 version of the nRF51 DK board. I could find only pca10028's hardware files in the nordic's webpage...
Hi,
I have some similar problem when trying to add the custom 128bit characteristic UUID.
The service UUID is advertised correctly but the characteristic UUID not.
...
Im using nrf51822 (16KB RAM), I'm trying to retain some data (RAM) after watchdog reset. when I load only the softdevice and my app, the RAM retention workings, but when I...
HI , ALL
i coded the uart_init in my project.
and i want to regarget the printf in my project.
so i find the retarget function is in the 'retarget.c' ,
i tried...
Hi,
We are using Softdevice S310 Version:3.0.0 and SDK:9.0.0.
My Device working on battery power. We are facing Flash write problem when my battery voltage goes to below...
Please tell me the safe 'Max Voltage Rating' for the capacitor at the DCC pin of the nrf51822 in DCDC mode. I am talking about the C12 cap in the circuit shown in Page 113...
