We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
I am working on the ble_connectivity example in nRF51_SDK_8.1.0_b6ed55f. A make error occurs when building this example.
Would you please tell me how can I fix...
If I understand correctly, a peripheral can distribute data such as UUID, device name, flags, appearance etc. between advertisement and scan response packets. To gather all...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I am having problems programming PCA10028 using nRFgo Studio.
Note I am using SDK V10.0.0 and IAR EWARM 7.5
Program SoftDevice with s110_nrf51_8.0.0_softdevice.hex ...
My platform is uVision V5.15, running s132 SDK ble_peripheral examples on nRF52 DK.
When compiling the system_nrf52.c in these examples, the error message was shown:
...
Hello everyone, I have an application that i would like to complete and I have most of it finished on Arduino but there are size constraints. Because of that i found the Nordic...
hi, what's the function of the code *(uint32_t *)0x40008C0C = 1 in GPIOTE example of SDK 9.0,
and i know the address of 0x40008000 is TIMER0, and i check the another timer...
Hello,
I a developing a custom application on a custom board with nRF51822 and SDK 10.0. I am also a newbie with BLE, so please bear with me.
I have succeeded in incorporating...
Hello everyone,
I would like to make the following application.
I want to connect a temperature sensor to nRF51822-beacon to broadcast the temperature measurements
...
Hi,
What does the "Enable services" button in the MCP do?
What are the Master Emulator API equivalent command to duplicate the "Enable services" button in the MCP?
...
Two questions:
If I use Nordic's library functions such as app_timer_create() and app_timer_start(), are the timers using the low-power RTC timer running with the...
After I connected a BLE device (HRM sample program on dev kit), I call sd_ble_gap_rssi_start to do a RSSI measurement, it returns error code 6.
Apparently error code 6...
Hi,
I've encountered a problem during development of an application based on ble_app_hrs_rscs_relay.
Everything works fine (I mean concurrent central and peripheral...
