Hey folks, we are planning to implement BLE Audio based on one of the Nordic ships and unfortunately nrf54H is not really available now and nrf54l does not support LC3 audio...
I'm trying to flash the hardware even with Programmer v4.6.0 but i get the following issue
18:59:55.179 Initialising the bundled nrfutil device 18:59:55.561 Using the...
Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
Hi there,
In our device we are using nRF52832 with SoftDevice S112, SDK 17.0.1 and embOS Safe. Up until now we were working with the “Just Works” setting of BLE connection...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
Hello Sir or Madam
Now i am using NRF51822 of your company. Now we are evaltion thermal character of this component.
So please kindly provide theta JC (junction to case...
Is it acceptable if I stop an app timer for dozens of times when the app timer is actually stopped.
Will the memory leak if I operates in these scenario.Does it affect whether...
I am considering using the nRF51822 for an upcoming project for a client. It is a simple BLE peripheral, so I would use the S110 SoftDevice for the stack. I am looking at...
I use BLE mesh github.com/.../nRF51-ble-bcast-mesh
but when I use the master control to write values to update the values of services, the following error occurs: "global...
Hi,
I have implemented the support for 'long write' as in
github.com/.../ble_app_hrs---LongWrite
which works from the MCP... except that on BLE_GATTS_EVT_WRITE, it seems...
I have bought nrf go starter kit with pca10005 board( nrf51822 ic). I want to program the nrf51822 using these tools.The guide that I got from the nordic website not explaining...
If the device is paired (but not bonded) using "Just Works", sd_softdevice_disable() causes the application to hang/crash (nothing happens until reset by watchdog timer)....
I want to generate 2 fast PWM waves with 25% duty cycles from nRF51822. They have same frequency of 4MHz but there is half a cycle delay between them. I checked the nrf_pwm...
Hi,
I am trying to get the NRF8001 rev. C chip working with a Tiva Lauchpad (TM4C123GXL) board. I modified the original Arduino SDK for use with Energia. I am using the...
Hello,
i want to write a global unsigned long variable in RAM after programming the device. The Use-Case is to set the clock value to the actual time. So the new unsigned...
I use BLE mesh github.com/.../nRF51-ble-bcast-mesh
but when I use the master control to write values to update the values of services, the following error occurs: "global...
Hi. All.
I am in the process of update SDK 9.0 from 5.2.
Meanwhile, SPI couldn't read from external flash's data.
Unusually SPI works well before infinite loop, I tested...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
I want to use the nRF51-DK board as a programmer for my target. As I understand it, this can be done with the signals on P19. However, there is one signal, EXT_RESET, that...
github.com/.../nrf51-UART-examples
Hey any I was trying to test the example, the one with BLE
I test
APP BLE sending --------shows on PC UART software
However, I can...
