Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
I'm trying to use the low-power comparator.
I've started up the comparator using "lpcomp_init()".
Following that, I wish to have a sample event, and then log the result...
I am trying the example here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_att_mtu.html
I want to lower the sleep...
Hi,
How do I enable Band 1 on my Thingy 91? On your web-page it seems that your base-band supports Band 1, but when I use the following AT-command AT%XCBAND=? I get the...
we are building some IOT devices for home automation, and things were going quite well since we tried to use our mesh network with two cell phones. we tried with two devices...
Hi.
I am using the NRF (Nrf52840) dongle to operate BLE devices (scan \ read \ write).
Is there a way to do it without the NRF connect application and just sending serial...
Hi,
I used Power Profiler Kit to measure our Custom module's current consumption. Everything worked perfectly.
Then I closed PPK SW and used SDK to flash new SW to one...
Hi,
I have connected nrf9160-dk to my laptop and using nRF connect v 2.6.2 with LTE link monitor application.
I am seeing only UART in green and Modem in Red. I am thinking...
Hello, I am making my first custom board based on nRF52832. I have used a custom antena design (due to PCB layout I did not use reference design). That was the very first...
Hi everyone,
We need your help with a condition that we encountered in our prototype of a nRF52840 that use a ceramic antenna. Our current design is poor and we will have...
Hello,
We have the following problem with a custom board based on the nRF52832 and the SKY66112-11 PA LNA, running as a mesh node.
The SDKs used are nrf5_SDK_for_Mesh_v3...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
My queries are:
1) In code I just changed...
Hello,
I have queries on Sniffer functionality.
1) Using nRF52840 USB dongle whether we can sniff BLE 5.0 packets.
2) Using nRF52840 development kit whether can I...
Here's is my device profile:
Running on SDK 15.2.0
FreeRTOS
Custom board, based on NRF52840
Powered by a 3.5Ah battery
Using CLI utility
Using the following...
Hello, we are developing a BLE application using SDK 5.2 and softdevice 6.2.1 (we are aware this is old, but we still have to support it).
We actually use Keil IDE 5.10...
