Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hi, I am developing firmware to run on a custom board using the nRF52810-CAAA chip. I need to meet very strict lower power consumption thresholds, and need to very precisely...
We are in development of a wearable ecg medical device. We want to add 4g low power capability. The device is a patch worn by patients 24/7 up to 30 days. Our current requirements...
Hi,
Is it possible to set CONFIG_HEAP_MEM_POOL_SIZE to be more than 16384?
I try to configure CONFIG_HEAP_MEM_POOL_SIZE = 94208 and when the heap allocated until 36830...
I have a device at -35 °C temperature, and sometimes I get the error "BLE_ERROR_INVALID_CONN_HANDLE" when in the ble_evt BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST. I'm using the...
For pairing key passing in ble_app_hrs, i have used the ble_app_gls example but it did not worked.
can anyone help me in how to pass pairing key issuse.
i have a question...
Hi! I am developing a network of temperature and humidity sensors, using nrf52832 and hts221 with the ide ses ... for this, I am using thingy 52 as a peripheral that sends...
Hi,
I have a project with NRF52832 and PCA10040 and SDK 16 and need to use both BLE and UART DFU. I can initialize and use them separately but I don't know how to use them...
Looking at the GPS driver source code, it seems there is no GPS hot start mode. In order to get the hot start working, do I have to modify the driver myself, or is there some...
have installed the software for Wireshark and I can see the interface in Wirshark, but I do not see and COM appearing in the Interface window nor does the sniffer appear as...
After many reboots, suddenly I got stuck at this error on every boot:
The data that's on the flash pages:
My mesh init params:
Using NRF52832, SDK 15.3.0, SD 132...
I have designed my own board, based around the nRF9160 but unfortunately I am unable to connect to an LTE network.
I am running the at_client code and using LTE Link Monitor...
Hello guys I am using nrf52840 interfacing analog sensors like potentiometer and accelerometer. This is not related to nrf, but I want to design a simple ADC filter that I...
Using a clean mesh sdk 3.2.0, I created a build directory inside the folder where I extracted the mesh sdk to.
Then, inside that directory, I used CMAKE with the following...
Hello,
I am currently developing a product using the nRF9160. I would like to use concurrently GPS and LTE-M.
I send periodically data to my server using LTE-M network...
Hello,
In the documentation on Infocenter for nRF52840 it is recommended to use P1.01 and P1.02 as low-frequency GPIO, while on nRF52840 DK those PINs are used for UART...
