I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I've read everything I can find in the documentation and on the forum about sdk_config.h. I also installed the CMSIS configuration wizard. However I'm still not clear what...
Hi,
For my project, firstly i erase all the user program, and then I install succesively the softdevice (s132 v6.1.0), the bootloader and my application software with nrfjprog...
I'm developing the Mesh DFU, and the source role is able to update the target role.
But now, we would like to utilize the method of broadcasting for transferring big data...
I'm running the at_client project one of our custom boards and am able to see the "AT host sample started" message, but it only responds to the first "AT" I sent. Any commands...
I'm using the mpu9250 connect to tca9548a and connect to the board, but if I move my sensor , sometimes twi read and write returns error code=3(but it usually don't happen...
Hello,
I'm integrating Nordic Mesh SDK into nRF5_SDK_15.2. I have following following guide for this:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
can any anyone suggest me how can i do this ble communication between those devices
i have used example program ble_app_hid_keyboard.
my question is i have to type data...
Try adding PA rfx66 to the device nrf52810:
#if defined(NRF52_SERIES) || defined(__SDK_DOXYGEN__) /** * @brief Set up external front end control. * * @param p_pa_lna_cfg...
Hi, I'm trying to using SEGGER IDE to program the nRF52840 whit both Zephyr RTOS and Nordic SDK accessible to my project. I have followed the guide on https://developer.nordicsemi...
Hi I still have problems with this board. I check it at my nRF dealer and it works. Yesterday I run it on an another PC and it works well:
But today at the same PC it...
Hello,
I am trying to implement the Peer Manager for bonding and pairing on my central device (nrf52840 Dongle) using SDK 15.3. I based my project off of the ble_app_uart_c...
Hello Nordic Semiconductor Community,
I do run mqtt_simple example successfully on my nRF9160 DK with modem firmware v1.1.1 and NCS tag v1.2.0.
Now I am connecting mqtt_simple...
Hi, I am using nrf52840 DK to create the uart ble app. The starting point is ble_app_uart example from SDK52 15.3. I changed pin configuration for uart so I can have RX and...
Hello,
I am looking into adding a whitelist to my central device to stop scanning devices I am disinterested in, however, I have a few questions and concerns about them...
