Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hello,
I face a problem which I can't understand really and where I need support.
It is strange...
In our electronics we use the nRF52840 which is enclosed in a module...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
Dear Engineer:
I am a developer of the nRF51822;Some costomers want to send a large number data over the bluetooth,So they require a high quality in speed;I want to know...
Hello,
I've noticed that it is quite hard to set up an Eclipse development environment and I want to try to make a package of everything that is needed for developing with...
Hi. I want to attach a sensor with SPI slave interface to the nRF52 Preview DK (PCA10036) using the SPIM1 with EasyDMA. Below I have two related questions:
In PAN...
It seems that in SDK9 the APP_BUTTON_INIT() macro has disappeared, and with it the extra argument that determines whether the scheduler is used or not.
However, the documentation...
Hi,
I want to develop one FOB key which will be in TX mode only to transmit a key continuously or at specified interval at ultra low power mode and powered by CR2032 coin...
I'm having really terrible RF performance with a PCB I've designed using a nRF51822 QFAC, Johanson 2450BM14E0003 balun, and a PCB IFA (from TI DN0007: www.ti.com/.../swru120b...
I would like to create a large “virtual” read only characteristic that does not fully exist in memory. I understand that large characteristics are transferred in chunks of...
I am trying to enable a critical section in handler. I need to update a sensitive global variable when a button event occurs, and the fact to enable/disable the interrupt...
I have nrf51822 and I use latest SD130. I scan nearby ble devices. In my case they are iPhones. When one device is in rage then I connect to it and start scan again and keep...
Hello to everyone!
So, now I try to enable a DFU for nrf51822 (S110 7.3.0)and have some problems with it.
I can't find a good example project including DFU, all that I...
I've created a simple test to demonstrate pstorage store/load for 64 pages of 1024 bytes each. To allow 64 flash pages I set PSTORAGE_MAX_APPLICATIONS to 64. Each page stores...
I've been following the custom service nAN-36 instructions and have it mostly working on my PCA10028 board, but I have two problems that I just can't figure out. I'm pretty...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
