Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I'm now using the lastest SDK 8.1.
I found that if I call app_button_enable() after app_button_disable(), app_button_enable() would not function again.
But if I changed...
Hi all,
I read that the nRF51822 comes as a blank chip from the factory, and this means that we have to program the SoftDevice ourself. I am wondering if this is the only...
Hi,
I'm using the Rigado BMD-200 Eval Board with sdk 8.1 and am running the ble_peripheral example titled ble_app_uart. I am using my iphone and the nRF UART app to communicate...
If using the button handling library the #define GPIOTE_CONFIG_NUM_LOW_POWER_EVENTS needs to be changed to add number of buttons being handled.
This wasn't clear to me...
Hi,all. i want to set tx power use interface "ble_tps_tx_power_level_set",and read back tx power level used tps servoce on my phone.how to do that ?Thanks for your reply!
Int the website:
link text
FEATURES show the nordice nRF51822 has 3 data rates (2Mbps/1Mbps/250kbps).
But , I set
number of packets transmitted per connection...
Hi,
If I want to run a blocked task e.g. write 1MB data to the external flash size 8MB(NVRAM), that it takes 3 seconds. What is the best way to to in NRF 51822?
Do you...
Hi,
I'm using the softdevice s110.
The power consumption is sometimes a little weird (around 1 mA). I think that the chip is in debug mode.
How can I know if the chip...
Hi,
The datasheet for nRF52 has pin assignments for QFN-48 only at present.
I'm using WLCSP package for the nRF51 and would like to know if there is any pin-to-pin compatibility...
have anyone successfully NRF51x,NRF52x series to interface with Matlab? Do you need to develop any additional code to do this?
Currently Matlab has support for BT Classic...
Hi,
I'd like to embed the nrf.exe utility used for creating DFU packages and uploading firmware via serial in a 3rd party app for use with our Nordic based devices.
...
Hello all,
I wish to set up the nRF51422 so that I can communicate with it via UART using the HCI protocol - I've been using a TI CC2540 device previously and there was...
Hi
is there a function with which I can check if indication or notification on a characteristic with notify or indicate capabilities has been enabled by the master?
