Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Dear All,
uVision debugger seems to execute code randomly. Picture shows stepping through the code. Codeline marking in grey also seems odd.
I would have expected to...
Hi,
I suffer from the phenomenon which can't sometimes maintain communication between the 32.8ms at Gazell communication at present.
When not writing in SoftDevice, this...
Hi,
I am using " BLE-Gateway " example from nRF51-ble-bcast-mesh to advertise my custom "Manufacturer Data" from 1 nRF51422 device to another nRF51422.
I've made the...
I have been able to implement the PER test (on nRF51822) using the direct_test_mode_s110 and code based off the example python code from the nAN34 zip file. I adjusted to...
Hi,
I want write a demon running on linux to control the 51822 dongle to connect or disconnect with mobile phones.
Now I have one idea, which is using string as command...
Hello,
I need to send packets that are larger than 20 bytes to once characteristic with a variable length. When I set the variable length to 100 bytes, the Attribute table...
NRF51822 supply voltage is 3V battery. When I design principle diagram, I have a question.
Both AVDD and VCC_nRF are connect with the battery's positive?
While trying to get the SDK's bootloader working with gcc, I have to replace some ARMCC-speific code found in bootloader_util_arm.c:
__asm void StartApplication(uint32_t...
I am using the nRF51-DK and have Timer1 setup as follows:
void start_timer(void)
{
NRF_TIMER1->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1...
Hi Guys,
I am currently using the ble driver for windows (Python) to get notifications from two Gatt services (Same Service/charac/descriptors/etc basically same application...
I've just trying to get SPI working, everything is compiling OK but when initialising the SPI, when the line below is hit,
/* Clear waiting interrupts and events */
p_spi_instance...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
I would like to support app_button, however I need to configure a pin as NOPULL and trigger on a low to high transition without debouncing.
I don't see a way this can co...
