Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
In SDK source code of S110 SOftdevice, I'v found two events for which module is registered and waiting using "softdevice_sys_evt_handler_set" & "softdevice_ble_evt_handler_set...
Hi,
I'm working on getting our product through BLE certification and they are asking a few quesion's that I'm not sure about.
1: Pairing. Is it using a fixed PIN or...
Hi,
Routine running normally in low power mode with power_manage() .
but after sd_flash_write/erase current consumption goes high(almost 20mA).
If anything is missing...
Hello,
i want to update the softdevice S310 V1.0.0 to version V2.0.1. My applicatio based on SDK 6.1. With S310 V1.0.0 all works fine. But i can't update to S310 V2.0.1...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello, I have a problem with GPIO Input control
My sensor work on special clock generated by MCU
I've controlled this sensor by Arduino like this
//SCK digital pin...
We are using the NR51422 to develop a BLE application. We reused the project “ble_app_hrm” from the SDK v6 and ran it using the NRF6310 board, everything is ok.
We just...
Hello Everyone, right now i use nrf51-dev kit and i want blinky code for that, in Keil i compile code and load in kit and it work fine but now i want to make code in eclipse...
I'm trying to debug the blinky example with SDK 7.1 using Eclipse Luna. Going through several threads here I could figure out configurations needed and build the app. I can...
Hi,
I have been trying to study how to implement support for over-the-air (OTA) updates in my current S110-based project. But I'm already stuck in the very beginning. How...
I am using softdevice and RTX at the same time.
RTX is using RTC1, softdevice is using RTC0, so no problem there.
But sd_softdevice_enable require a clock source as one...
Hi,
I have problem with nRF51 antenna orientation. I used nRF51 developement kit (mKIT) board and I had problem with communication if I just change a little inorientation...
Can I change the shared channel address (first one or first two bytes in the message) when the channel is open?
The manual says after opening the channel, send a broadcast...
