I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Since I've migrated to SDK 10 and updated all my toolchains I've noticed that when I debug on Eclipse, when I run my code nothing happens properly. However if I pause and...
There are various examples in the keil microvision examples for DTM.
The list is below. Is there a difference between these examples?
Which one should we use if our design...
Currently the default for the SPI0 chip select is active low. I would like to change it to active high. Can I do this?
If not can I just have the SPI chip select on a pin...
Continuing with my attempts to get this to work on SES I'm not sure if I'm missing something simple or not.
So using the excellent RKNRFGO (which by the way is much quicker...
There is an error in the gcc makefile included with SDK 5.2.0 that prevents it from detecting when a header file has changed and automatically recompiling the C files that...
Hi all,
I've always been a CSR developer and recently been asked to develop on the Nordic chip. The example code makes sense to me and its not to different to the CSR code...
Hello,
I have a custom board and I am trying to verify the maximum throughput on NRF51822. I am able to communicate with Android BLE stack, however, I need to increase...
Hello! :)
I am a beginner with micro controller programming and want to start with a nrf52
Could someone please explain the difference between the development kit...
Hi,
we have a project in which we have to scan a lot of beacons (up to 100) with Active Scan (scan request and response). We tried to implement this system with actually...
There's an example saadc_pca10036 in the SDK. I am wondering how this piece of code works in that example:
void saadc_init(void)
{
ret_code_t err_code;
nrf_saadc_channel_config_t...
I am working in the SDK10.0 ble_app_uart_c(master),it can connect to ble_app_hrs(slave) successfully.
But if I add a new 128 bit UUID named ACC_BASE_UUID different from NUS_BASE_UUID...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_multilink_central" for reference.
Multi-connection function is OK.
Whenever I connect to peripherals, I can see connected...
I am trying to change analog-to-digital (SAADC) sampling interval when sampling using Easy-DMA in nRF52832. The code looks like follows (error checks removed for clarity)...
Hello everyone,
currently I'm working on a project with an NRF51-SoC. I want to use a MEMS Oscillator as high frequency clock source this is working very well so far. But...
