Hi,
I would like an nRFX example on how to set up DPPI using single in (1 Event) and multiple out (2 Tasks). I have previously done this using the fork functionality in...
Hey all,
Every time I flash, I get the following error message:
Error: One or more batch tasks failed: - [Probe] Device error: Memory access error at 0x00000000. Probably...
Hello everyone,
I would like to learn how to create unit tests using the ZTest framework for a Nordic sample project, in order to better understand how it works.
I am...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hello,
Yesterday, I received a new Power Profiler Kit 2 device directly out of the box, and unfortunately, it is not detected by any PC.
Symptoms: - The green LED blinks...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
I am building my application up on the blinky free rtos. I want to use RTC and ble stack. i am initialising RTC1 first and ble stack stact.
The problem is that I am getting...
I am using nordic nrf8002 BLE with a breakout board & not a developement kit. I gave 3.3v supply in different combinations:
(1)3.3v to vdd pin-1, GND to vss pin-4
(2)3.3v...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
How can I calculate the maximum throughput for an application running on the nRF51822 and the S110, when connecting to different kind of Central devices?
If we want to obtain sets of five "Bluetooth stylish temperature sensors, do you have a selling point in The Netherlands? If not maybe a way to obtain this by mail or parcel...
Hi!
I am coding soft for nRF52xx. Having looked through the examples I've got one question.
In the preprocessor defined:
NRF52_PAN_24
NRF52_PAN_25
NRF52_PAN_26
NRF52_PAN_27...
We have a nrf51822 chip connected to an arduino-like device. We need to use UART for communication, but without firmware modification the master chip doesn't support USART...
Hi.
I'm using PCA10028, SDK10.0.0, S130. I'm a beginner.
If I want to download hex files(soft device and fw code) though UART port, is it possible?
If possible, could you...
Dear all,
I checked the SDK release note and found Nordic decide not to support CMSIS anymore.
As I developing with 52832, I try to use FreeRtos to control the whole system...
Hi: I want use freeRTOS on nrf51822 based on sdk10. But when I open the example project"blinky_freertos"and try to use it, The keil5 manage run-time environment tell me "install...
I am developing a BLE peripheral with SDK9 and SD110. The PPCP are 80-400ms, 5 slave latency and 5s supervision timeout.
I am currently running some blocking code in response...
I'm having trouble with my call to ble_advertising_init when using S130 soft device v2.0.0 on an 10031 device with SDK 11.0.0, I'm getting error_code 7.
When I try and...
