Hi,
we are working on a test program with a thinghy:91 board based on the example "asset_tracker_v2" and we are having issues with some SIM Cards.
We are using iBasis...
Nordic TS,
I'm trying to establish a link between two 9151 DK through which I can pass messages. I'm trying to create a setup where DK 1 receives messages using a DECT NR...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
As a life-long embedded software engineer I'm used two or three dozen of different setups, SDKs, IDEs - but all had in common I can copy or clone a project, open, build and...
Hello,
I am new to modems and cellular domain.
We intend to design and build a cellular communication extension for an older product. And I eyed the nRF9151 for that....
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
Hello,
I have been attempting to implement a system on my custom nRF5340 board where the external QSPI flash (IS25LP) is shared between eXecute-in-Place (XIP) functionality...
Yeah. It's that topic again.
I tried to measure the current with an oscilloscope (Agilent 100Mhz; 2GSa/s).. but that didn't quite work.
Can you maybe share how you guys...
Hi
I have tried to convert ble_app_uart to use spi slave rather than the uart with no success.
Please can I have some pointers as how to go about it.
Thank you
Hi,
system info:
SDK: v6.0.0.43681
S110 V7.0.0
nRF51822 Rev.2
I’m using a ~4ms one shot timer (using the timer library) which is being started in the...
How can I dynamically assign the MQTT broker address
Hi all,
I have a general question how to assign the MQTT broker address dynamically.
Current Nordic IoT-SDK mqtt...
Hi,
my question is related to this question:
devzone.nordicsemi.com/.../
Erasing Flash pages takes a pretty long time (and the CPU is blocked during this time). For...
Hi,
I use NRF51822 QFAC chip, SDK is 8.1.1, soft device is S110. The base project is ble_app_uart. Now I want to add OTA DFU into my project. But I don't know how to start...
Hey together,
I'm using the GPREGRET register at the nrf52832 to determine how the module should start up after an off mode reset. Thus I set a predefined bit in the GPREGRET...
I have been working on the multilink example lately (version: 8.0), I have identified the function to send data on the peripheral part, it is sd_ble_gatts_hvx(), but I'm having...
hello ,
my IDE is keil and the sdk is nRF51_SDK_10. i know the system is 16M frequency,but now i only have 32M crystal.How can i change the sdk if i wang to run the system...
hello , Nordic Engineers. my IDE is keil and the sdk is nRF51_SDK_10 and s110_nrf51_8.0.0_softdevice.hex. The project is "C:\Users\robben\Desktop\nRF51_SDK_10\nRF51_SDK_10...
Hi,
I am trying to load hex file over the air for nordic but I am getting error as master emulator installation not found. Please suggest. I am using MCP of version 3.10...
hello i want To use mbed for nrf51 dk. i used this link developer.mbed.org/.../ . i am following steps but i can't copy hex file into bootloader. i got error message "There...
Hi,all
my question is in the title.
i am making a project like NUS (sample in SDK).
i found that during the data transmission Situation，the write without response...
