Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I need to do this, A product ble and Gazell should be used. Switch bluetooth or Gazell mode by pressing the button, but ble and Gazell not used the same time.
When I switch...
condition:i am using the nrf51_adk10.0.0,and i want to enable the NRF51422 as a central role.,so a program the sd130,and i download the application into the board(ble_app_uart_c_s130_pca10028...
Hello,
I am using nRF51822 to build a product and employ 3.0V battery as power supply and system works on DCDC mode. I need RTC counter to do real time tracking. My question...
Hi,
I am developing a glucose application using nrf51822 chip.
Now i want to go for mass manufacturing.
All my devices are advertising the same name.
I want to identify...
Hi all,
I was testing with a new nRF51 Dongle recently and am finding that it disconnected from any peripheral after 15-18 seconds. Generally a little while after a Connection...
I had a PWM question ( here ). It was recommended that I install SDK 10 and use the PWM files from SDK 10. I installed and copied the PWM files from 10 to 9 and opened my...
Hi, I've compiled program from this link:
developer.mbed.org/.../
The problem is that I can't connect to my DK by nRF UART 2.0 app, probably because not every UUID is...
I am working on adding a timer in the ble_app_uart sample, aiming on disconnect with device which doesn't send any data in specific time, such as 5 seconds.
Now I have...
I get NRF_ERROR_SVC_HANDLER_MISSING error in spi_open function.
uint32_t err = sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type);
APP_ERROR_CHECK(err);
I'm using...
hi,
I need to store persistent data of about 32 bytes in flash, so tried using pstorage APIs (SDK v9.0 on nRF51822 -- 256KB ).
I followed the sample code given here...
Hello,
I am using keil uvision 5.17, sdk 9.0.0 and sd 130.
Once I programmed whole application through mbed,
Then I moved into keil and implemented all function....
We are trying to communicate to NRF51422 through PC using UART communication. But the programs works fine with nRF51822 Dongle and DK. But it does not works with another dongle...
Hi experts,
I need nrf51822 to send thousands of packets (notification) to Master Control Panel (PC), and expect for high data rate. So, I turned the connection interval...
if initial uart_config() before ble_stack_init(), softdevice_handler_init will be failed!
with SDK 6.0
softdevice_handler_init() will returns 0x00001001 ("NRF_ERROR_SDM_INCORRECT_INTERRUPT_CONFIGURATION...
