I am getting a bt_hci_core: HCI driver open failed (-11) with a custom board using nrfConnect for VS Code and 2.9.1 toolchain/sdk.
The code is really simple (I'm not...
Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am trying to connect nRF52 with 7120 and create a NFC card reader , is this a solution and power efficient solution .
I will interface through I2C , is there a example...
I am using the sdk version 11 and arm-none-eabi-gcc version 5.4 on linux mint to compile the blinky test application. I have pointed the Makefile-posix at the location of...
I am doing the test about timeslot with the project link text
but it cannot scaninng and i found the timeslot is work because i get event NRF_EVT_RADIO_BLOCKED and it call...
Hello,
my application has to emit measurements in the manufacturer specific data structure continuously and has to accept a connection, for example for ANCS. Therefore...
Hi,
I am developing a firmware using nrf51822xxaa s130 SDK 10.0. I am using device manager to exchange the security keys and storing the bond information. For my project...
Hi, If I understand correctly the debugger on PCA10040 can operate in 6MHz/n as SWO frequency.
the nrf52 can operate at 4,8,16,32MHz swo frequency.
How are we to use SWO...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
I'm trying to implement the DFU Feature into my application, but it seems to be in a bootloop after it starts advertising.
The application works fine when flashing it via...
Hello everyone, I want to measure Low power mode current consumption in nRF52 DK,but I dont have accurate CRO to measure in micro Amperes, therefore I would like to know if...
the eclipse build memory map is
text data bss dec hex filename
363312 2485 5340 371137 5a9c1 ********.elf
363312 2485 5340 371137 5a9c1 (TOTALS)
it is giving very large...
Hi Friends, I like Nordic and Arduino, it's great if Nordic can support Arduino officially, we can use the ARM0 in Nrf51822 as a single control point of Arduino project. There...
I taken the Android-nRF-Beacon-for-Eddystone app code from github.
From my account I configured my Google Dev console:
enabled proximity API
added credentials...
Hi all,
I followed the tutorial listed below:
devzone.nordicsemi.com/.../
I want to use SEGGER_RTT_printf but I always get this error:
Error: L6218E: Undefined symbol...
