Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
Hi, I've been given an nRF52 devkit and have been tasked with programming to generate a 2.4GHz signal. The requirement given to me is that simple. (I believe an RF expert...
We moved a Zephyr project to SDK 3.0.2. After that it is possible to compile it on Mac and Linux machines but on WSL I'm getting an error:
Looks like I miss some environment...
I'm using nRF Connect for VSCode to program my nrf5340dk but the SDK can't detect my nrf5340 on the boards (You can see in the image). Can anybody help me to fix this problem...
I am new to Zephyr RTOS . i have a breakout board of Max32664D from protocentral interfaced to nrf52840 development kit . i want to get started with this sensor hub max32664...
Hi,nordic team
Iam programming with nrf52833 and ncs v2.9.0
I am doing DFU by myself.And I Flash_write data into slot1_partition,I am sure my data write in flash is correct...
Hi I am starting with nRF9160. I build and program "nrf91_simple_tracker," but while running, I got the following terminal output:
I am using nRF Connect SDK v2.7.0 with...
Hello,
As soon as we enable CONFIG_BOOTLOADER_MCUBOOT and have an operational MCUBoot image, we noticed that our audio pipeline is no longer working for our i2s omni-microphone...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Hi
on any example in nRF Connect SDK, for nRF9160 (but even for other SoC):
- how can I enable Serial Recovery in the software? any config to select? (I guess I need also...
