Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi
After reading different threads I figured out that I can program my Smart Beacons kit using NRF51-DK. Correct?
And to do so I need TC2030 tag-connect cable?
If yes...
I am using the spi slave example code from SDK 0.9.2 and connect the board to an Atmel SAM4S who is the SPI master. I can see that every time the CS signal is released from...
I want to make nrf51822 with accelerometer.But Keil compiler dont know.What I do?
It was given as examples of programs I want to do. devzone.nordicsemi.com/.../.I
I want...
Hello Guys,
I want to go with nordic solution for the bluetooth low energy application. Can anyone please explain me how much it will cost to develop your own module including...
hiii....
i am developing a custom profile with five services... i want to make these 5 services and its characteristics available only for some authorized devices.. ie...
I am working on a custom service using and nrf51822 device. SDK7.1 SD7.1
My security parameters are as follows:
#define SEC_PARAM_TIMEOUT 30 /**< Timeout for Pairing...
Hello,
I am running the UART app example in SDK 0.9.1 with the nRF52 and PCA 10036. I am using putty to send and receive messages, as well as the nRF UART v2.0 app for...
Hi,
I'm currently trying to determine the power consumption of my nrf51DK during different states of my program using an oscilloscope. To do so, I am using an external power...
We had been trying to use SD 7.0 with SDK 6.1.0, but realized our libraries were mixed up and not controlled very well, and we were experiencing occasional crashes where the...
Hello,
I'm looking to find a way to send a 32 bits number to the ledButtonDemo with the Master Control Panel (I have the Nordic dongle).
Indeed, I replace uint8_t led_state...
Hi,
I have a question regarding the NRF 52 boot sequence.
When we first receive it from Nordic, what are the boot options? Are there any other options to load a code on...
Hi,
I'd like to know how to set/alter passcode when pairing happens. I looked a few examples in Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\8.0.0\ble_peripheral but...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi all,
If i have connect a band with my phone, then i let my band close to my notebook and let my notebook unlock.
Any suggestion about this?
Thanks in advance
Hello all,
I am working on the implementation of DFU OTA in our application, running on a custom board using the nRF51822-QFAC.
The tools that I am using are:
...
