Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
hi,
i want to restart my timer before it expires.
suppose my timeout is 2 second and i want to restart it in between 0-2 second based on signal when i receive before expires...
I've notice that the ST Balun NRF01D3 that I've used for my current design is not listed as compatible with Rev 3 (Build code: H) nRF51822 Silicon. Has there been any change...
Hi everyone,
I am looking into Crossworks and SEGGER's Embedded Studio and since they are related I am wondering which one of them is more recommendable? Right now Eclipse...
Hi,
I have set ble_adv_fast_timeout = 0 (same problem with ble_adv_slow_timeout) to get advertising forever, but when in call sd_ble_gap_adv_start, i get error 0x07 (param...
Hi all
According the nRF51822 Product Specification V3.1, the 16MHz RC oscillator has a tolerance of at most 5% and can be used as clock source for the UART module.
...
Hi,
I am trying to change an example code on ble_app_uart_c (Central) SDK10.0.0 s130.
I have changed already peripheral example and I can see notification data if I...
Hi,
while flashing the device i get "Contents mismatch at: 0001C1C0H".
I am not sure if my IROM1 and IRAM1 settings are setup correct in the Target Settings of my Keil project...
Hi,
i have two microcontrollers: STM32F401 and nRF51822. They communicate by uart with flow control. I use 110 Soft Device from SDK 10. The maximum baud rate when communication...
Hi All,
I am trying to update the HEX file of LED_mesh example using DFU bootloader over-the-air. The LED_mesh application HEX file gets uploaded successfully by bootloader...
Hi Nordics,
I copy pwm sample code into my proximity project, to drive a buzzer .
I init pwm before softdevice. but, once "SOFTDEVICE_HANDLER_INIT" is excuted, the buzzer...
Hi,
i have a problem with nRF51 an nRF24LU1+. I use S110 and micro-esb library. I can switch beatween poroperty RF and bluetooh ( never run both in the same time ). When...
I wanted to use the SysTick timer for timing in my application, but even when writing a handler and trying to set it up, it doesn't seem like the interrupt is ever triggered...
hi I am i using Keil to debug the progam, it seems like that the printf() function can't work in keil, so i use jlink RTT to perform the printf function to collect data ....
HI,
i want to have a application in which a timer timeout say 5 second. and during this timeout there is another timer say 1 second. whenever the 1sec timer timeouts then...
