Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi, I have an application where I am recording button presses using a beacon-like implementation. The button presses represent start/finish events for a race and are communicated...
In my setup, i have a Node with SD130 as peripheral to Smartphone and as a central to a BLE peripheral.
I need to store some Unique ID about the Smart phone and a Peripheral...
I find out that
The s110 can only connect to a single
central, but is able to do
non-connectable advertising while in
that connection
by here
So is this...
Hello,
I have a problem with the sd_flash_write function. It HardFaults on me and I can't seem to find out why. The Addresses are 4 byte aligned...
The function is called...
Hello,
I have written a timer driver with timer 0 without SD and used 24 bit mode and it is working.
But when I used the same driver with softdevice and Timer 2 and...
I have a problem enabling TIMER1:
If the prescaler is set between 16MHz and 2 MHz the firmware fails to enable the SoftDevice, even if I didn't manage TIMER0, but TIMER1...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130.
Does anyone tried...
Hi,
I'm now going to combine the proximity program with the ancs program, but I don't know how to make it.
When I try to add the proximity program to the ancs (I add tps...
Hi all,
I want to upgrade current SD from 7.0 to 8.0 by DFU, and try it as followed:
1.Use the nRF Toolbox 1.12 in Android;
2.Select 'Soft Device' as the file type...
I have nrf51822 with latest sd130.
I need to implement central what connects to smartphone. Phone has two characteristics with HVX. First char is sending one byte after...
I want to Communicate with two Nrf51822 device
The slave (S110 SDK6.1) will do a echo function .
For example Get uart data and will send out same data but over BLE.
And...
iOS's auto connect introduces a number of unpleasant corner cases that can be difficult to deal with.
One annoying error path is if you delete the bond data on the peripheral...
Hello ,
I am initialising application timer with prescale of 327 for 10 ms interrupt delay. I created a timer slot using app_timer_create(&ulTestTimer, APP_TIMER_MODE_REPEATED...
