Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Is there an example that is a minimal example of advertising on S110?
It might even serve one attribute that is set to a constant like '1234'.
This would help me bring...
HI
I am trying to use mkit as programmer by P20
FOR third part BLE brd
VDD---mkit.vdd
GND--mkit.gnd
SWD--P20.4
SWC--P20.5
bisides, for
P20.3(SH_VTG) connected...
We're going to be programming and debugging our prototype nRF51822 board using this adapter from Segger. It's the same connector as comes with the J-Link LITE in the dev kit...
Dear Nordic Team,
I am using Nordic DK board,
Now i want integrate UART to hid-mouse application. So that whatever data i can receive , will send to HID device without...
Hello everybody,
I'm trying to use pstorage module but it seems that the example_cb_handler function is never called when I try to store data.
I noticed similar issues...
There have been a number of other older topics with this same error message symptom, but I've tried all the solutions proposed and none have worked to solve this specific...
Hi.
I am using SD s110, ble_app_uart example from SDK10.0.0 on dk pca10028 as a peripheral. The central is a laptop running linux.
I am trying to establish a connection...
As noted here , a lower interval will give quicker connection - but at the expense of power consumption.
With a 4s interval, it seems that it is likely to take several...
Let's say I add two PPIs which both trigger off of the same event. One of these PPIs is connected to the CHG[0].EN task, and the other is connected to the CHG[0].DIS task...
In the GTT_2_Introduction nRF52 document there is a picture with text
-42 dB Selectivity (2'nd CI). As far as i concerned it's about Carrier-to-interference ratio. But what...
Hi.
I am using DK PCA10028 V1.1.0 for my devlopment. The SD is ver 8.0.0, the SDK is the latest and keil v5. The IC is nRF51422QFAC. I am trying to flash the examples from...
Hello, Is it possible to configure nRF's USART to work with Smartcards (ISO 7816)?
The ISO7816 specification defines the bit rate with the following formula:
B=(Di/Fi...
I use the " nrf51-ble-dfu-symmetric-signing " example from GitHub.
The application download over dfu works fine on the PCA10028 board.
But how can I install this bootloader...
dm_distributed_keys_get returns address of local variable 'peer_enc_key';
sdk version: nRF51_SDK_9.0.0_2e23562
in function ret_code_t dm_distributed_keys_get(dm_handle_t...
hello guys,
I'm working in a project & I added some sort of security to the project, I enabled the bonding & MTIM flags through:
#define SEC_PARAM_TIMEOUT 50 /**< Timeout...
