Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
when phone connect to the device, I print the connected address.
However, I find that the bluetooth address is not same with the phone bluetooth address.
here is the debug...
Hi,
I am trying to include temperature (read from DS18B20) in advertisement data using BLE_UUID_HEALTH_THERMOMETER_SERVICE. So far it works fine, but my temperature is...
Hey,
I am using twi_hw_master.c and twi_master.h libraries for twi and want to disable i2c to save power when not in use.
I use the following two lines to disable the i2c...
Hi,
i am using Eclipse 'Mars' and Segger V5.10c to debug some of the SDK examples. The Eclipse command line shows only binary garbage. How can I get the garbage readable...
Hi,I am using s130 softdevice and SDK9.0 .I add static passkey(123456)in my project base on ble_app_uart project and basic functions have been achieved.But I have a question...
Hello!
Is it fine to ready NRF_RADIO->FREQUENCY right after receipt of BLE_GAP_EVT_ADV_REPORT?
Does its value have a relationship with recent adv. report?
hello there when i am trying to open project C:\nRF51_SDK_8.1.0_b6ed55f\examples\ble_peripheral\ble_app_template - Copy\pca10028\s110\arm4. i am getting error like
Third...
Hi,
I have set connection interval as 1.8s.
But i have transmit data every 1 min.
I noticed that BLE transmits data every 1.8sec.
Can someone please tell me what is...
I have just exported a project from mbed, to the Keil uVision4 tool chain.
Create New Project "BLE_Thermometer" on mbed.
"BLE example for the Health-Thermometer...
I see in the information about the nRF51 talking about the support of 4.2. But it is not clear to me the extend of it. I am focus on the link layer and I would like to know...
Is it possible to implement 2 peripheral in one device (need to connect a peripheral device with two different centrals)? When should i expect for this feature?
I have a question about how much memory is required for app timers.
The comments for APP_TIMER_BUF_SIZE state that the buffer size must be one more than actually needed...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
