I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi all,
I can use the API sd_ble_gap_rssi_start to start RSSI and can get the value when the BLE_GAP_EVT_RSSI_CHANGED event occurs.However,when I use the sd_ble_gap_rssi_stop...
Hi, I'm recently concerned with the latent risk that nrf51822 might be hacked by extracting the firmware also known as "snarf"ing.
And I know there is Memory Proection Unit...
I followed the guide of github.com/.../nRF51-ble-bcast-mesh to try the mesh with NRF51822.But there seem no discribtion about which softdevice we should use.I loaded the s110_nrf51822_7...
Use SDK6.1 / SD7.0, iOS9 can not pairing!
dm_ble_evt_handler() return error "BLE_GAP_SEC_STATUS_UNSPECIFIED"!
It is the captured packets file: ble_proximity_ios9.1.pcapng...
I can't find an implementation for the indoor positioning service in any of the SDKs. Should I assume it's not implemented? If so, are there any plans to implement it?
...
Hello,
a presentation given at the nRF52 Global Tech Tour stated that one of the planned features for S132 and S130 was a support for multiple peripheral connections (2...
Hi
Now I'm using the S130 and ble_app_uart.I meet some problem need your help.
Firstly,I download the code to PCA10028,then it can connect to nRF UART on the iPhone5S...
Hey,
I am a bit confused with "client characteristic configuration" that is used to enable notifications (at least in Android).
To enable the notifications I have to...
The manual for my Agilent N4010A Wireless Test Set talks about a BER test based on a "vendor specific loopback test mode". This mode would allow me to do BER measurements...
Hi there,
I am starting with nrf52 and SDK 9.0.2 and am struggling with the SDK structure.
Can anyone please explain the difference between
components/libraries/uart...
Hello, I have tried to combine saadc with softdevice, but having errors during compiling. I have copied .c and .h files from saadc example to ble_hrs example, but having following...
Hi,
I have a specific application/product where in I am planning to use Nordic nRF52832.
-> There is a 9 Axis Inertial Measurement Unit (accel/gyro/magnetometer) connected...
Hi!
I have been trying for over a year to figure this out, but I am unable to, and I would hope it be pretty straight forward since OTA is already in the Nordit Master Control...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
