Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
The documentation for the nRF52840's SAADC mention optional resistor ladders. What are they for? I see that the documentation specifies that the ladder's resistance is 160kΩ...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi,
I'm trying to transfer data received from BLE to SPI. When the handler of my service in BLE is achieved I transfer the data I received to SPI.
I know the max that...
Hi all,
I am using ble mesh code, it has version based. For my application( needs to blink led synchronously in mesh) i don't need version part, so i tried with using if...
As your datasheet, External HFXO's Run current is 250uA, but HFINT case is 60uA.
Despite lager current, why do you use HFXO in reference circuit?
I would like to use HFINT...
using **nrf_drv_saadc.**c and nrf_saadc .c nRF52832 with sd132v2.0
for example.
i init a app_timer to update a adc channel per 10ms.
and manually update the batt volt...
Hi
I'm trying to send adc value from peripheral to central. I'm using nrf51822 with softdevice s130_1.0.0 and SDK v10.0.0 .
I'm getting error 3002 which I figured out...
Hi everyone
I am trying to understand if it 's possible to change the clock frequency on-the-fly, by giving a certain command to the uC via UART.
I started from the...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hello,
I'm using nrf51822 with a few sensors and nrftoolbox app in my smartphone.
In nrftoolbox SW, I can just connect and see what happens in sensors.
I want to control...
I need to use Timer 0,1,and 2(I have only 3 timers 0-2 in nRF51822xxAA). This means, I cannot afford to let the BLE use a timer(I can certainly afford to give one RTC for...
Hi,
I'm trying to update attribute value and notify it to client using sd_ble_gatts_hvx() function:
memset(ms, 0, sizeof(params));
params.type=BLE_GATT_HVX_NOTIFICATION;...
When I use sd_ble_gatts_hvx() to send data to iOS and Android device I meet a problem:
Data send to iOS ok,but will return error 8 (invalid states) when send to Android...
Hi,
I am trying to use SPI to get data from a sensor. In nRF 5 SDK V11, I got it to work by setting the SS pin in the config struct of the initialization function.
...