Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi.
I have a question.
I use nRF52 Preview DK, PCA10040, SDK11,
I tryed some examples in nRF52_SDK.
Some projects moved,and some another projects didn't move.
I...
I don't find the information in the nRF51822 documentations and in this forum.
How can I know that? Is there some register to check, or some hints to know that debug mode...
hi,
i am using the nrf51422 and trying the UART example ( in order to connect the nrf51422 and a stm32f4 using serial connection)
what i didn't understand is what does the...
I am using a nRF51822(pca10028) for current measurement. I had set up the devices as told in user guide. I am using SDK 11.0, softdevice s130 and default ble_app_pwr_profiling...
I am trying to make a custom BLE service and be able to do debug it with UART at the same time.
Just trying to print some UART messages at some points in the code.
However...
I have a couple of questions with the MCP.
Before knowing MCP, I've been connecting with my nrf51-DK with the nordic master control app installed in my smartphone. Opening...
I am doing burst transfers using exactly the code suggested here devzone.nordicsemi.com/.../
The problem is, the data is received three times by the receiver (three times...
Hi!
I question the use of Software Interrupts and especially SWI3.
I'm currently developing an
application on nRF51422 based on
SDK10.0.0 and SoftDevice S110
v8...
I know that it can be done and I have read the other posts. I'm still running on SDK8.0.0 with both a S110 and a S130. Using wireshark and the nordic sniffer firmware on a...
hello everybody,
I need to send some data on the value attached with the notification:
/**@brief Function for adding the notify Level characteristic.
*
* @param...
My application need more than one of the host in the same area, we will set difference pipe of each host, we want to know the area already exist which of the pipe. Then we...
Is there a way to avoid fees, and still use BLE? Do I need to change UUIDs or leave them be?
If not can the nrf51822 be used to just use the pure 2.4 ghz protocol and DFU...
If a BLE device using nRF51822 has a freuqency drift around 80kHz (BLE limit is 50kHz). All other measurement item like ICFT can pass the BLE spec. Will the performance of...
Hi, this is my very first post to this forum.
I just received my nRF51 DK, so I installed a lot of stuff. The blinky example is running fine.
A question about nRFgo Studio...
