board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Hi,
Has anyone test with Nexus 5X ?
I could not change connection interval 7.5ms, the interval is always 45ms.
Does anyone know how to change the connection interval...
SDK 9.0, examples/ble_peripheral/ble_app_hrs
Trying to use DFU with a bond device, I got aware, that after the update, some "static" data seems to get corrupted during...
In the Keil Pack nRF_Libraries V3.10 [SDK V10.0.0?] (Low-Power PWM Example)
Not a big Bug, but an inconvenience all the same.
low_power_pwm.c line 165
ret_code_t...
Hello,
I want to change the advertising timout during runtime. We have two use cases for our device:
Batterie mode --> advertising timeout = 2min
Power...
Hello,
Implementing a LED led driver was pretty simple and below code works well:
nrf_gpio_cfg_output(LED_PIN);
nrf_gpio_pin_clear(LED_PIN);
NRF_GPIOTE->POWER =...
Hi there,I am using the PWM library in github github.com/.../nrf51-pwm-library . After I do this in my project and I check the pin output with Oscilloscope but didn't see...
I have a product that was released a few months ago and is operating in-the-field. Recently we discovered a bug and need to fix it. We are unable to do a DFU because:
...
Hello,
DEVICE_MANAGER_APP_CONTEXT_SIZE should be less than 256 bytes in size.
However, it seems to work properly (not fully tested) whith a size of 800 bytes, and no more...
Hi all,
I want to make sampling from microphone at 16KHz. So I want to first disable softdevice, do all measurements. An after that enable softdevice to transmit data. Will...
Hi,
Recently, I am playing around with the NRF51 dongle and trying to make it work as a BLE master.
However, when I run the sample code(e.g. advertising, multi-link .etc...
Hello, i am seeing a strange behaviour of pstorage module and i don't understand what is happening. I have read links below:
pstorage-problem-on-power-off
saving-data...
Hi,
I haven't been able to find a clear answer to this.
With the ESB protocol, a payload can be stored in the PRX TX FIFO to be sent back to the PTX as part of the ACK...
I have some nrf51422s beacons and wondering if they can send and receive data. So I want it to keep transmitting its id and signal strength but if somebody is reading the...
I am trying to implement the ANT+ Environment Profile using the nRF51 DK and I was wondering if anyone had done this and could point me in the right direction to start. I...
