Hi all, hope this is the right place. I'm developing a small breakout board to test/program the NRF52805; this board will eventually be expanded to include a pressure sensor...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hello.
After some great struggles, we've managed to enable WiFi and encrypted socket + TLS connection to google.com and various websites.
Since then, we've been looking...
In Electrical specification Table 1 (current consumption in forced High Power mode) lists a typical value of 7.2 mA , just want to confirmed this is correct and not a typo...
Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
Hi
I'm very new and looking at the PTR5518 breakout board. The docs below specify some of the pins:
Are the pins EN , RX , TX , RTS etc. tied to P0.08, P0.09,...
Dear Sir/Madam,
I want to use the One channel of Timer 1 for PWM generation and other channel is used to measure the pulse width of input square wave.
For above i need...
When I try to step through my code, I get a wdt event firing. I have tried setting the behaviour to pause during debug and sleep
void wdt_init(void)
{
uint32_t operationStatus...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
hi,
can i use timer interrupt has more than 1ms period??
#define APP_TIMER_TICKS(MS, PRESCALER)
((uint32_t)ROUNDED_DIV((MS) * (uint64_t)APP_TIMER_CLOCK_FREQ, ((PRESCALER...
Hi, I'm trying IOT SDK now and I got some questions
My devices: nRF51422 DK, nRF51_iot_sdk_0.8.0_f1f6187, iot_ipv6_coap_client_pca10028
Q1: Why is the advertising interval...
Hi Nordic support,
I am building the ble_connectivity project of the latest SDK11. My EVB is pca10028m, the project is located under "nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral...
HI,ALL,
in the Blue Core Spec, there are such statement here,
L2CAP permits higher level protocols and applications to transmit and receive
upper layer data packets...
Hi, I use [nRF5_SDK_11.0.0\examples\ble_peripheral\ble_app_hrs\pca10040\s132],but I get error such as the following.
{
............\components\softdevice\s132\headers...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
HI, I am new to embedded system and just start to learn NRF52 DK. currently I want to configure a pin of nrf52 as interrupt. so i created new GPIOTE_Handler function . however...
hi, i am getting a lot of help in here, thanks a lot
i'm using SDK 6.0.0 for my project. and i want to use timer as a counter like as the title.
then, i fount the app_timer_cnt_get...
hello,
I am using S130 softdevice. While I am trying to connect with MCP I am getting one error with error code :0x08. and MCP is showing a message like "Lost connection...
