Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am trying to add static passkey pairing to ble_app_uart in SDK_11 s130. To do this, I first implemented static passkey successfully in ble_app_gls using sd_ble_opt_set(...
Tl; dr
I tried to use OTA DFU with Public BLE Address, but I failed. Is this possible?
Details
Condition
I modified ble_app_hrs example like below (SDK11, pca10028...
I have a radio board using a NRF51822 with a custom radio protocol. I need a unique identifier, ideally 24bit, 32bit but be acceptable.
I notice in the parameters there...
I've looking through as much of the documentation I as I could to read more about the radio timeslot api.
I looked through the SDS document and the chapter on the Radio Timeslot...
I am able to use eclipse to run simple project, but after move the real one, getting lost of errors:
www.dropbox.com/.../Screenshot 2014-04-02 09.10.41.png
I add required...
Hello,
I just received my BMD-200 eval board today and cannot get any of the examples working. I started out trying to get blinky to work using GCC and the make files provided...
I am trying to port peer manager implemented in ble_app_gls to ble_app_uart using instructions in devzone.nordicsemi.com/.../ . I am using SDK_11 s130 on nRF51-dk.
I encountered...
hi all,
i am using SDK V8. i want to start and stop the RTC manually .i gone through rtc periheral example but still i am not getting . please help me. i am a beginneer...
Hello,
I am using the nRF51822 with SDK 10.0, S110 softdevice, and a SPI slave interface. The SPI slave interface works , but the standby power consumption of the nRF is...
Hi there,I am using s130, my device is now working at peripheral mode, it's advertising. I want to switch it into central mode by pressing a button. and switch back to peripheral...
If I had two devices, one set up as a peripheral and one as a central, what sort of factors do I need to consider to work out the lowest possible power consumption/average...
Hi,
I am sampling 2 200Hz signal using ADC and transmitting data using heart rate and battery service of ble_hrm(instead of using simulated data).
But since the connection...
I have the following setup:
nRF51 dongle
connectivity_115k2_with_s130_1.0.0.hex firmware
Windows 7 PC
nrf51-ble-driver_win_0.5.0
My app is written in...
