Hi,
As the subject says, I have an nRF54LM20A acting as a SPI slave. When I perform a call to spi_transceive_cb(), I don't have any data for TX (i.e. MISO). This runs until...
Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board - works on DK
Summary
On a custom nRF54L15 board, the PDM peripheral clock ...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hello,
I am using PCA10028 and sdk 12.2.0. Now I have interfaced temperature sensor and I am storing 4000 readings from sample to flash. Once all the 4000 samples are stored...
When I enable DLE with a max MTU size of 247 (NRF_BLE_MAX_MTU_SIZE = 247) and PDU payload size of 251 (opt.gap_opt.ext_len.rxtx_max_pdu_payload_size = 251) and a max characteristic...
log.txt I have programmed my nRF smart beacon with example peripheral code with DK52. My beacon now flashes red. I am using the nordic sniffer to sniff ble packets in wireshark...
Hi,
I will be using ble_uart application code in my nRF52 Evaluation board. With nRF52 EVK I will be connecting external module over UART communication. I want to detect...
i am having trouble with pwm module 2. only two of the channels are working but not the third nor the fourth.
i tried pwm module 1 but im having the same problem there. i...
I'm currently working on an esb project using two nrf52832 chips wherein PTX regularly sends packets to PRX as a kind of heartbeat monitor. I can't seem to find what happens...
Hi,
I get the ble_app_att_mtu_throughput -example working with the coded PHY between two nRF52840 boards. Very nice, although I did not yet get the coded PHY advertising...
Looking at the ble_nus service, I see that the SoftDevice allows notifications to be more than 20 bytes long:
uint32_t ble_nus_string_send(ble_nus_t * p_nus, uint8_t *...
I'm try to use RTC1 to generate overflow interrupt, but it doesn't trigger interrupt.
void RTC1_IRQHandler(void)
{
// do something
}
main()
{
NRF_RTC1->TASKS_STOP...
Hi,
I'm using s132, sdk 12.1 on nrf52x, my question is about possible race condition when setting the value of a characteristic using sd_ble_gatts_value_set (on peripheral...
Hi,
I am working on a IoT based project with nRF52832 and nRF52840. I am looking for PCB Designers and people who can develop firmware for our project. The firmware development...
Hello, in S110 device's nrf_sdm.h, there is this enum "NRF_CLOCK_LFCLKSRCS" which is defined as:
enum NRF_CLOCK_LFCLKSRCS
{
NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, /**< LFCLK...
Hi..!
I am trying to ***Receive ACCELEROMETER DATA FROM MPU6050 to PCA10028(NRF51822) AND WANTING TO PRINT IT ONTO UART using KEIL IDE.
Code is getting compiled & getting...
HI.
I want to send data from nRF24L01 + to RF communication and receive it from nRF24LU1 +.
The nRF24L01 + is connected to the STM32. The settings are as follows.
...
Hi, I'm trying to build a bluetooth device that pairs once, and does not have other hosts maliciously or accidentally pair to it (which would create a poor experience for...
