I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
Hi, is there a sample using nRF7002 on nRF54LM20B SQSPI (or could you share an appropriate devicetree)? I have been successful using the nRF54LM20 DK + nRF7002 EBII combination...
Hello.
I have nRF52840 USB Dongle connected to PC with nRFConect desktop application 4.0.4
I'm trying to connect to our custom BLE peripheral device, which advertises...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I have modified the Multisim example code slightly, and I am using it to make some demo code for myself. I installed the Nordic Bluetooth sniffer, and everything seems to...
Hi,
Im using Keil, S110 6.0.0 and a ble_app_hrs demo code.
I get a problem that the code hangs in sd_softdevice_enable. The board is a copy of the board from the dev...
I am using the sniffer with Wireshark to watch some data being passed by my central and peripheral. I started with the multilink central and peripheral examples. Unfortuantely...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
Folks,
Here's a specific question and a larger question, of which the first is a part.
What's the proper way to insure S110 BLE stack cleanup on disconnect due to...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi all,
We're currently working on the project with includes external ADC. The SPI interface is used for communication, we're using spi_master library from the newest SDK...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
I have an nRF51822 based peripheral running SD 7.0.0, using SDK 6.0.0. It has a custom (vendor specific) characteristic which is read/write.
If I use BLE_GAP_CONN_MODE_SET_OPEN...
Hello Guys,
I am interested in what is the packet size of Heart Rate application board example included in nRF51 SDK 6.0. I am using nRF51822 Evaluation board. Could help...
I am working on nrf24l01+ which interfaced with atmega32. I received data but it take time to receive (appx. 1min). I set RF_SETUP to 0x27 ,disabling auto ack and sending...
I consider to use a 32k MEMS oscillator instead of a usual 32k quartz crystal with a nRF51822 (WLCS). 32k MEMS oscillator's package is quite small 1.55 x 0.85 mm, there's...
I am developing on a custom board using nrf51822 with pure gcc. The blinky makefile worked fine. Before going to ble_hrs makefile, I want to load the blinky_example with softdevice...
hi guys,
i've a general question about bluetooth (general usage of characteristics), and i hope somebody could give me a hint how to use them properly.
So, i want to communicate...
