Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have to transfer 256 bytes over BLE using a nrf51822 with s110 SD. I have used the steps in the guide in this post: devzone.nordicsemi.com/.../ and it works fine...
Hi all,
The ble_app_keyboard demo could not connect to ipad smoothly like followed operation:
1.use two iPads(ios8.2), iPad A and iPad B;
2.use the ble_app_keyboard...
Hello there,
I have a question about compatibility of dongle with ble_peripheral examples.
I have been using pca10028 nRF51-dk running ble_peripheral examples (+S110)...
Hi,
I am using nRF51822 controller for my development. I implemented the system sleep mode as below.
for (;;)
{
power_manage();
}
void power_manage(void)
{
uint32_t...
Hello, I found that there has been SDK update for NRF52 regarding NFC. Currently, it looks like NFC is just used for tagging.
I'd like to know whether I can use NFC peripheral...
Where can I find the BLE_GAP_EVT_ADV_REPORT value if I am using S310 SoftDevice?
Without it I cannot use my client to get advertising data from server. Or is there any other...
Hi Nordic：
I have two questions about SoftDevice s130：
Device A,B,C,D are using s130.
When this device (called A) is a peripheral and connected with a tablet...
Dear Nordic developers!
I am working on a project, which should use the ANT+ and the BLE communications, too. The S310 SoftDevice is good for them, but I have some problem...
Hi
I have been reading a lot of posts and the documentation on DFU for SDK7.2, but something is not really clear to me.
When I compile and program the boot loader in my...
Has anyone added an external power amplifier to the nRF24L01?. For my application, I need to increase rf power.
What about a skywork Amplifier ? if there is any amplifier...
Howdy all,
Has anyone added an external power amplifier to the nRF51822? From what I recall the BLE spec allows for 10mW output power (well, 10mW would be the maximum for...
Is there any recommended chip antenna for NRF52 SoC? Any guideline on the antenna placement, designing the matching circuit etc? I assume for NRF52, no need for an external...
