Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi Nordic
I am wondering whether one device can connect to two Bluetooth devices at the same time and independently control the TX power to communicate with the two devices...
Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
Hello Nordic Support Team,
I am experiencing a startup issue with the nPM1300 PMIC. Below is the summary of my hardware configuration and the behavior I am observing:
...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I have a new nRF52 Preview Development Kit, after connect it to a computer with a USB cable, the status light (LD5) come on, indicating it has power. However, the standard...
I am working on a project to integrate nRF51822 with a rechargeable battery,
and make it chargeable through micro USB cable.
Any recommendation on the battery model, charger...
I have a dual mode BLE / ANT+ nRF51422 design going through regulatory testing for FCC / EU marketing approval. I have previously successfully tested a very similar design...
The spec of nrf52 mentiones 'Propriatary RF' as option. I was wondering if that could be used to implement 802.15.4 which would save us an entire IC and power and like basically...
Hi there!
I would like to implement the nRF24L01-module to one project.
But, it would be great, too, if i can use the application manual to use only the chip itself with...
I have the nRF51-DK development kit (PCA 10028). I'm following the gcc tutorial here - devzone.nordicsemi.com/.../.
I'm using the ble_apps_hrs project as a basis for my...
Is it possible to connect DCC / DEC4 to a transistor to turn on / off a part in my circuit? I assume yes, but I just want to make sure.
Or, is there another way to turn...
Hi again,
If I use BluetoothGATTSetCharacteristicValue and set wr_auth = 1 in the ble characteristics, I receive a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event. I can also see...
Dear Nordic developers,
Does TWI supports bit level clock stretching? Means that after each bit (not byte) slave can hold down the clock and master should perform appropriate...
So I have the following bootloader code:
int main() {
uint32_t code;
sd_mbr_command_t mbr_command = { SD_MBR_COMMAND_INIT_SD, };
code = sd_mbr_command(&mbr_command...
My ANT BLE application runs on a custom board with a nRF51422, SD 310 rev 2.0.0
I can use the nRF UART app on an android phone, but on an iPhone with iOS 8.4 I can't even...
Hello,
I'm using an PTR5188 development board for my project which breaks out PIN 26 & 27 for ADC only. I'm using mbed as my development platform and haven't been able to...
Hi there
Can you clarify a point for me?
Quoting from Gazell link layer user guide:
"If only the ACK packet sent from the Host to the Device is lost, but both the initial...
Hello.
Reading the documentation of pstorage_load and the actual implementation has left me with confusion.
The documentation states that the size and offset parameters...
