Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I'm developing an application based on SD130 1.0.0 (latest) and DevKit board with 51422 chip.
The application uses timer for some synchronization purpose. Operation with...
Hi
Maybe I'm getting stupid, but I'm having problems to program my new nRF51 DK kit. I was working last year with the previous version with no problems, but with this new...
Hello,
I noticed the various examples as well as the ble_advertising component all check for pending flash operations and will not start advertising until they are all...
hi guys,
im developing a program to interface accelerometer MMA8452 with nrf51822.so if accelerometer is in peripheral device,how do i send the x,y,z co-ordinates from peripheral...
Hi everybody, i am working with a nrf51822. S110 with sdk6.1 IDE:keil
I want to do FLASH Erase while in a connection.
I have read this page devzone.nordicsemi.com/......
On initialization of the bsp, I get ERROR 4 (NRF_ERROR_NO_MEM) when I define LOCATION.
Why is this? Because it seems rather weird there's no more memory at that point in...
Hi all,
When I start the bootloader using ble_dfu service as-is in my application I get no ble events in the bootloader. When I call the bootloader from the main loop it...
I have a sample program that is failing on sd_ble_gap_device_name_set with an invalid parameter.
It's calling BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode)
And then it passes...
Gentlemen: Do you have posted a copy of the original firmware that comes installed on the nRF51822 beacon? I have been experimenting writing my own app on that beacon, and...
Hi all,
I have an TICK interrupt on RTC1 on nRF51822, but the program keeps cycling in the interrupt - as if the interrupt is never cleared?
Here's my code:
void...
Hello,
I am currently building up a little application on top of the ble_multilink_peripheral_example.
I would like to have the nRF Master Control Panel on Android to...
Hello,
First, my setup is as follows:
nRF51822 Rev. 3 dev board (PCA10028)
s110 7.1
SDK 6.1.0
I am developing firmware on the PCA10028. I am matching SPI to a custom...
Well not my best title. But I hope you can follow this explanation:
I added RTT to my project to replace UART. It works so far. But there is a strange behaviour...
Code...
