Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
What is the best way to transfer an array of individual values using the BLE stack?
Is it by appending all the values into one blob and sticking it into a characteristic...
I'm using
HID keyboard example (SDK 7.2), Softdevice S110 7.1 , IAR for ARM 7.1, J-Link,
on my custom board (with NordicSemi nRF51822-QFAA MCU).
/***************...
I am designing a product with the nrf8002 chip and have a question on Power consumption. Lets say I leave all the default ratio's alone and use a CR1620 battery which has...
How can I read the Bluetooth clock (piconet) which is synchronized between the master/slaves in the piconet ? I need a constant (micro second accuracy) time from when I do...
Hello,
Is it possible to know the preamble , data format and the CRC calculation to interface a radio system ( GFSK Manchester) with NRF905 ?
Thank you
I'm wondering if the port and pin function can be used together to configure a set of pins.
For _port_dir_set, I assume it sets the whole port to the designated direction...
Hey i was using the code from developer.mbed.org/.../main.cpp
I am using this chip ( http://i.imgur.com/q8EM4uq.jpg ), it is nordic nRF51822 but i exactly do not know its...
I am using spi_master.c for spi communication with nRF51822EK.
And i had sent and recieved data packet successfully for 1st time with spi_master_send_recv(). When i sending...
Hi All,
I can compile and flash examples with my nrf51822 SDK on linux. I would like to use Code::Blocks as IDE.
Code::Blocks is transparent to run debugger. I try to...
I bought a blend micro to learn about arduino and BLE. I am a complete newbie in this field.
This is what I want to make happen,
I want to install my Blend Micro inside...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
My nRF Studio can not get nRF6130 board info,just show "Boards connected:".
But I can download fw to nRF51822 chip on the nRF6310 board.
The Application "ble_app_hrs" is...
What is the cleanest way to expose a dynamic (non-fixed amount of entries) through BLE?
One way I thought of is to create a service for a single table entry and go through...
Hi all,
I have an nRF-DK (the new one that's mbed compatible: developer.mbed.org/.../)
I have managed to completely brick it by copying the wrong file onto the BOOTLOADER...
Have tried to use an external interrupt coding.
/*------------------------------------------------------------------------------------------------------------*/
#define...
