Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi sir We have requirement Blutooth 5.0 for iot Appication. please can you share the schematic file
their is orcad capture design file or available or PDF file
Currently evaluating Bluetooth mesh and trying to use the Zephyr mesh_demo.
I added so that the instead of buttons triggering the bt_mesh_model_send from the main loop periodically...
now I'm on NRF24Le1 project, and I have a problem with wakeup TICK from timer or voltage level on pin (analog comparator wakeup). could you help me ? or have you an example...
Hi,
Is assisted GPS(AGPS) supported in nRF9160?
Our nrf9160 custom board takes 2 to 5 minutes for the first fix with active antenna. Does nrf9160 support AGPS data to...
Hi,
We recently purchased a thingy 52 for evaluation H/W 1.1.0 F/W 2.0.1
We are using an iPhone 8 with the latest Nordic apps.
When we connect using the the Thingy app...
I am new in nordic and just getting started with the nRF52832-DK. . Can someone please help me ? How to read 4 Digital Input and store it into SD card.and then pass that stored...
Hi,
I was using SDK 1.0.0 earlier.
I ported my code to new SDK v1.0.0.
But i am getting undeclared macro error as shown in below image
In prj.conf i have initialized...
Hi All,
I have arduino ble 33 ble device and able to connect with it using my android application using BLE library. I am trying to write 9000 or 18000 of UINT16 by converting...
hi ,,, i am getting the four data from various sensors, then i want to combine all the four data and send in ble_app in variable , example x=10;y=30;z=34 using sprintf i am...
Hi,
I want to use the nRF Mesh SDK on nRF52840 chip with proxy client role that can send messages over GATT connection to proxy server role device. Is that possible?
Currently...
Hi Nordic,
Chip set: nRF52840
SDK: 15.3.0
Softdevice: S140 (06.01.01)
Button interface with MCU: Total=13 (All with GPIOTE)
We have face one blocking issue at...
Hi, Greetings !
I have totally 3 services and 8 characteristics added in my project. In first service there are 2 characteristics, 2 nd service there are 5 characteristics...
Hello Support Team,
I am using an nrf52832 module in our project. During testing, we have observed that the BLE firmware gets stuck and it stops advertising further when...
HEllo; I'm working with nrf52832 and sdk15 , and for interrupt button i chose to work with the example "/nRF5_SDK_15.0.0_a53641a/examples/peripheral/pin_change_int/" , so...
