We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi
I am using SDK V. 15.3.0 and Softdevice S132 6.1.1 on a nRF52832. I am developing two devices, one of with is battery powered and one that is connected to a serial interface...
Aside from the connection interval, I'd like to know if the 2Mhz phy is enable along with Data Packet Length Extension and Connection Event Length Extension.
Is there...
The modem_info module in nRF Connect SDK returns various modem parameters to the application. The function "modem_info_params_get" fails to update the following paramters...
We are running an application in dual mode (central + peripheral) where we relay the data from the peripherals up to the top central. Is it possible to control the priorities...
As a user I need to include stdbool.h before including lte_lc.h. lte_lc.h uses the bool type but does not include the appropriate header, so I get compilation issues if I...
use sdk:11.0
Reference routine：ble_nus_c
now I use 52832 to connect a device,the service UUID like the photo.
when I only discover one service UUID,like this code...
I am using an ADC where the SPI MISO pin also acts as a data ready pin when it transitions from Hi-to-Low as detailed in the link below. I am able to configure this and it...
Hi, I am new in Mesh using nRF52840, when I try to build the light_switch example, I link to all the libraries that project need and change the SDK_ROOT to the direction of...
The password I was assigned was 8 characters. I am so sick of these sites requiring logins and passwords that can never be remembered and frankly serving no purpose. I have...
=======
SDK: 15.3
Product all base: ble_app_template
Problem: cannot update iBeacon content dynamically during system run-time.
=======
we try to use ADV with...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
Hardware: nrf52DK PCA10040
nrfutil version 5.2.0
Hi,
I am trying to get the...
We have a custom nrf52832 board. We have nearly 260 boards. After uploading the app through DFU app (nRFConnect) , the new application starts to advertise . The application...
Hi,
We are using NRF52840 in our project.I am using SDK 15.3 and soft device s140 in keil 5 uvision. The NRF52840 Bluetooth will act as central and the other controller...
