I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I am trying to communicate between an ADXL362 accelerometer and a nRF9160 DK. I see on this link https://docs.zephyrproject.org/latest/samples/sensor/adxl362/README.html that...
Hello
we had purchased nRF6700 and nRF24LE1-F16Q24-DK from Mouser India on 14-oct-19 .and it comes with an older version of firmware i.e.(3743) And currently, I am facing...
Hello:
I have to nRF52DK boards and I am able to run the ligth_switch example, but the thing that I want to do is send a message, "hello" from one node to other. I saw...
Sir in the above code i have a cmd_zb_match_desc() but i am calling inside the switch case but after calling i didn't able going inside the finction
please give the Suggestion...
HI,
I want to send heart rate data to smartphone using NRF51422 in every second without any time delay or minimal time delay ranges between(0.9 to 1.1 sec).
Thanks...
Hello,
I managed to get a central application to run on the nRF52810 with SDK 14.2 and S132 V5.1.0. I also got the bootloader working with this setup.
Right now I'm having...
Hi!
I have nrf52 periperial mode, SDK15, s132.
I connect a smartphon in the central mode to my nRF52 and start to send some data.
In the nRF52 I receive those data in...
Hi, I am trying to print double/float values, but Its printing blank. e.g. printk(" value:%.3f\n", value); output: value:%.3f printk(" value:%lf\n", value); output: value...
My project consists of reading an NFC card's value (using another chip), and respond to the interrupt generated by that chip to read the value from it using SPI. Then, this...
Currently I am using VS Code for development. Mostly everything is fine and VS code is awesome.
However there are some problems I am facing.
1. It is time consuming to...
Hi,
In my application,for the first time device (nrf52832)will start advertising and on nrfconnect for mobile application side we make it get connected and bonded.It may...
Hello! I'm trying to develop an Android-nRF-Toolbox App. What features and folders do i use with show logs? In order to develop the uart in the toolbox app, we have deleted...
Hi everyone,
I want to know that is it possible to send the heart rate data using HRM services without sending the battery data in nRF51422. When I disable the battery...
Hi! I've been working with the Thingy 91 and I've found that the SIM card was running out of data, so we decided to buy more data to keep working. The board was working as...
