Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
I am not able to send ble_nus_string_send 8th time when I am calling it for 8th time. That is it is sending 140 characters. I am sending data from nRF51822 using ble_nus_string_send...
Try as I might all searches for anything related to sd_rpc_* give 'no results'. Admittedly the search engine for the online and offline documentation is poor/difficult to...
Hello,
On our current hardware there are no IO pins left to add any dedicated U(S)ART connectivity. Therefor is there a way to perform any kind of serial monitoring via...
(I am currently trying to learn Zigbee) (Updated entry since I believe I was mis-reading the log and the ZC is ACK and not NACK)
I am currently trying to get my endpoint...
Sorry for asking, maybe stupid questions, but looking at ble_app_hrs_freertos example in SDK 16.0.0 cant get through:
1.to documentation ble_conn_params_init_t. first_conn_params_update_delay...
I'm trying to get IQ (or MagPhase) data from nrf52811 chip. The datasheet indicates that I can get the data from address indicated by DFEPACKET.PTR. Is there any example code...
Hello,
I'm quite a beginner programming with the NRF52 and all and while trying to debug any example and view the log and error messages I simply can't see it anywhere...
Hello, I have read posts about programming external boards and want to use BC832 as a beacon. I have been trying to program it with nRF52840 DK and followed these operations...
Hi Devzone!
I'm using uart to send AT commands to LTE modem.
but when I send AT commands the response is quite strange, and I think the command is sent twice. I don...
Hi, I'm using the Zigbee SDKv3.1.0 Cli agent as coordinator, the Zigbee SDKv3.1.0 Ligh_Switch example and two commercial light bulb (Ikea and Heiman) I'm be able to command...
Hi,
TWI init using nrf_drv_twi_init, if event_handler is null it will be blocking mode. My question is, which one is less power consuming? block or non-blocking mode?...
Hi Everyone
*ITS VERY URGENT ISSUE*.
I am using nrf52840 PDK with segger embedded IDE.
I was trying to use the QSPI module to write data to the external flash memory...
Hello All,
I am trying to send data on serial port of nrf9160 to be published on a topic using MQTT protocol. So far using the mqtt example and UART example, I have successfully...