Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
After Christmas update we are unable to use DFU from Android devices.
We've been using such function on a regular basis with our devices and everything has always been fine...
Hello everyone,
I'm using a NRF51822 as a central device, I connect to a peripheral (NRF51822-based device), then I stop the scan. At a later time I initiate another scan...
Hi,
I am trying to program nRF52832 custom circuit with nRF52 DK, I have connected debug out from the nRF52 DK to the custom circuit containing nRF52832 debug in. When I...
Hey Guys,
i am currently experimenting with the NFC functionality and have an issue with our "nrf52840-DK" boards:
i am testing with IAR (8.40.2 - including the library...
Hi there,
I'm trying to use serial library from SDK to interact with cellular modem (AT commands, not nRF9160). I've read documentation (library description, api). May be...
I have build and flashed the zephire/sample/bluetooth/hci_uart on nrf52840 board and connected the board with ubuntu but hci interface was not created when checked using hciconfig...
Hi,
We have chose LCD which has only 3-Wire support CS, CLK and DI so we have connected that pins with nRF51822 chipset. Now Please see the below image which shows that...
Hi All,
I want to read/write long characteristic (200 bytes max) from Android to my device.
I'm working on the 15.2.0 SDK and S140 Softdevice.
I read some Q&A on...
Hi there,
Right now I am doing some dry research into long range Coded PHY for S=8 or S=2 since I need to have some extra room in the link budget to go the distance. The...
Hi, I'm trying to adapt the ble_gateway example for nRF91dk to use a nRF52 instead a Thingy52. When I change the UUID at ble.c from Thingy to nRF52, I'm not able to get a...
Hello guys,
In next few months I've to put down a new design for a medical product. Both nRF52840 and nRF5340 would fit well the application requirements. But I think this...
I want to use two UARTS ie uart0 and uart1. I read that nrf51822 gpio pins can be set as rx & tx but i couldnt find any example.
I am using SDK12.3
Please attach some...
Hi,
I've looked around the DevZone for answers to this, and haven't quite seen an answer, so I'm going to post my solutions here.
I am using the secure bootloader from...
