Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi, I am trying to get the BLE values on Thingy91 (PCA20035) . And I have followed the
devzone.nordicsemi.com/.../217018 I have ported the diff (nrf and zephyr diffs from...
I am using built-in DTLS for encrypting my UDP traffic. In order to save expensive data quota and reduce battery drain, I have to make use of session resumption, so that I...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
I am developing a firmware on a nrf52840 board with FreeRTOS. Unfortunately, due to a mistake during the development process, the board misses the XTAL 32,768 Hz.
Is there...
Hi Nordic:
I want to build a raspberry connected to a 52832 board via uart,
this raspberry pi with 52832 board need doing secure DFU to remote BLE device, the raspberryPI...
Using the nRF9160 on the Verizon network we are having some issues with eDRX. Specifically sending data to the device from our MQTT server.
We have configured a eDRX interval...
Hi,
I am working on nrf52 msc example. I am required to use internal flash for msc. In example there is support for ram, sd card and spi flash. I am required to use internal...
Hello,
I'm currently trying to sniff the DH Key Exchange as specified in Spec 5.1 p.2446. I'm using the nRF51 Dongle as sniffer, the nRF52 DK as slave and the nRF52840...
Hi,
I am using two nRF52840 DK in which one of the board is flashed with light switch client and other one is flashed with light server and a nRF mesh app is used for provisioning...
Hi,
I see Nordic has recently released an updated software to do direct test mode (without the use of python or the old nRFGo studio). I am able to run the test code on...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) While upgrading over serial interface using DFU, whether UART needs...
Hi,
If you are interested I would to contribute to https://github.com/NordicSemiconductor/nRF-Sniffer-for-802.15.4 repository. On the python driver part. You could allow...
Hello
I'm doing a test that if it's possible to start ibeacon function when BLE is connected in nRF52840. so I merge ibeacon into HRM demo code and as you can in the following...
Hello ...
Our BLE peripheral product (nRF52810, SDK 15.3.0, SD 112 6.1.1) is relatively simple. iOS device (central) connects to peripheral. Data is exchanged between the...
Hi, i'm new to Nordic devices and i hope this topic hasn't already been treated. I'm triyng to debug an example application; after the first breakpoint, i loose the control...
