Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi All
We have to send GPS data to Cloud but we do not have network so is this possible to send GPS data from nRF9160sip to ESP32 via UART communication
and after using...
Hi ...
how to send the particular message from client to specific server in mesh ? i am using mesh 3.1 version
i want to use 4 server and one client . client have to send...
Hi
We use the function "sd_ble_gatts_value_set()" for setting new values of a characteristic(not changing the length). This function takes between 120 and 260 us time to...
Hey,
I was wondering if I can write C++ code for the NRF9160:
Does the NRF9160 DK support C++?
Is SEGGER IDE compatible with it?
Is it recommended to use C++ in...
Hi:
I use the SDK 13.0 and nRF52 DK to develop software for the project. Based on BLE UART (NUS), the software do SAADC sample and transfer the data out in real time, The...
I have recently ported our working project to SES. The project uses S140 with nordik SDK 15.20 on nRF52840 custom board. the project also makes use of freeRTOS. It's important...
Hello,
mqtt_simple was probably never tested in TLS because some parts for TLS are missing (see client_init)
Could you make a good exemple that works please ?
hi...
I am working with thingy52 while compiling i am getting this error , then i moved to segger , in segger i am getting following errors
how to overcome this ? help...
Hello -
We are interested in using NimBLE for a nRF52 project as we've used NimBLE on another micro controller. NimBLE would be running on FreeRTOS and we are developing...
Hello everyone,
I'm trying to generate a periodical sine signal at the output of a 10 bit DAC without CPU interaction. The DAC uses an SPI interface, thus my idea was to...
I am trying to run adafruit_tag_reader example on nRF52840 DK .
Problem :
If these are my pins in sdk_config.h it works fine
Whereas this doesn't work.
nrf52832 softdevice S132 SDK15 custom board
TWI instance
TX(nrf_drv_twi_tx) failed, slave device is AD5252 digital potentiometer, i want to send data to the potentiometer...
Hi Sir,
I want to sent specific message to a defined server with a static ip configured. Kindly let me how we can do this in nRF9160 with NBIOT network.
Regards, ...
