Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
When calling sd_ble_gap_connect(), and providing a whitelist, what is the expected process for establishing a connection, as far as timing is concerned? Will the device scan...
nRF52840. In case of standby current (battery only)
Measured as follows:
With only the battery connected, the same current draw as the one attached. Is there any...
In my DFU bootloader I am protecting areas of Flash memory used to store user data.
After an update, when my application starts and tries to write to this memory it is causing...
I am trying to use the real time clock on the nRF52840 dongle using the pc-ble-driver. However, my nrf.h file has nothing in it but the following:
#ifndef NRF_H__ #define...
I have a working iBeacon advertising a beacon UUID, Major, & Minor on a nRF52832. In addition, I also have a single BLE service (which has a single characteristic) defined...
Hi I am managing to initialize a serial instance using uart0 within the BLE Buttonless DFU Template. However when I carry out a similar process for uart1 I get the following...
Team,
I received the following customer inquiry and hope you can help:
The BLE – WiFi bridge project I’m working on will need to control up to 64 nodes, not concurrently...
Hello,
I am trying to upload the firmware with secure DFU using following method:
generated the dfu_public_key.c and private.pem pair
copied the " dfu_public_key.c...
Hi Dear Team,
I am using the nRF52840-Dongle and pc-ble-driver-py-0.12.0 for the ble development, while I encounter a problem about the max connection per device.
I use...
Hi,
I've got some questions about setting up a connection.
I want to connect as fast as possible with a UUID filter. Is it possible to connect directly on the first advertising...
How to set 250kbps PHY Coded in NRF52832 BLE Mesh? I have tried to change scanner_config_radio_mode_set(RADIO_MODE_BLE_1MBIT); to scanner_config_radio_mode_set(RADIO_MODE_NRF_250KBIT...
Hai ,
I need to update nrf52840 over ble from esp32 . first i tried with app , firmware gets updated .. as per the dfu protocol i understood flow and tried to writing data...
I need atleast 10 UART channels to be configured in my project. Is it possible to do it with the NRF52840. I believe because of the PPI I should be able to do this. I was...
I want to create a small bluetooth device with the nrf52823 chip. I want to use a lithium battery cell to power the whole circuit and therefore it neet to be low power. On...
